I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
want to know how can i judge that the variation is caused in the connection interval, connection supervision timeout, slave latency once i have flashed ble_app_template code...
Hi, Is it possible to estimate the power consumption cost for sending data based on information provided by the modem?
Note from nRF9160 HardwareVerification Guidelines...
I was trying to connect to NRF52-DK using this Python script:
https://github.com/thomasstenersen/pyrtt-viewer/blob/master/pyrtt-viewer
It runs fine on some machines, but...
SDK Environment: nRF Connect SDK v1.7.1 Target: Decawave DWM1001-DEV. This uses the nRF52832
Simon posted in this discussion an example of adding a custom service to the...
Dear Members,
I followed the step on :
https://devzone.nordicsemi.com/f/nordic-q-a/71299/getting-hardfault-error-when-using-ble-lesc-pairing/292979#292979
and I got...
Hi,
I'm developing with 52832 DK. I used 'CONFIG_NFCT_PINS_AS_GPIOS' to config pin9, pin10 as general GPIOs and set pin10 to SPI_MOSI. However the system crash when applying...
Hi,
I am creating a BLE communication device (peripheral) using softdevice S132 (v7.0.1) and SDK 16.0.0 on the nRF52832 microcomputer.
I have implemented the BLE communication...
Hello,
I'm new on Nordic environment, I'm designing a RF module that require low latency to transmit few bytes (less than 10) in less then 10ms from a triggering input...
Hello,
Referencing the specification , the time it takes to complete the COMPARE task upon triggering is not directly outlined.
I would like to have the following function...
Hi,
I've installed VS Code 162.3 on Windows 10 machine via Toolchain Manager. I've also installed nRF Connect extensions for SDK v1.7.1. The build system works under NCS...
We need to know the list of configurations to explore more like the following configurations in proj.conf file
for C++ files we enable following configurations in proj...
I use cli library functions for serial port communication, using macros to define m_cli_uart and m_ m_cli_uart _transport variables, program compilation is no problem, when...
Hello everyone,
I used the Multirole example as base for my code. My target is to make a communication with two NRF52382. I changed the HRS (heart rate servide) to my custom...
Hi,
I am using the PCA10040 DK (v1.1.1) to measure the current consumption in sleep mode and the current is about 200 uA. (3V, DCDC Enable)
Following is the code, it...
