I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have a problem about BPROT function, the project is on nrf52832 and using SDK 15.3, Softdevice s132 6.1.1.
If I enable the BPROT function by calling nrf_bootloader_flash_protect...
Nrf52832, SDK 13.0 Softdevice 132 PMIC: bq25150
I have a battery powered BLE device. When a user takes off the battery and put it back and powering on, the device does...
i set the connected time is 30ms
but i use dongle to grab the bag ,i find that the connection parameters were wrong , it can not fix at a value
it looks like it change...
Hello,
This issue is related to this ticket , before continuing I recommend to read it first.
I had suspicion that the "speed" improvement is between project compiled...
Hello,
I recently opened a ticket, with several questions about the mesh network, I had some evolutions and new questions emerged.
We have a firmware already consolidated...
Hell there Can I find an SDK that is supported on Nrf52805 chip? Or can I get any proper guidance on program of nrf52805 (the module MS46SFIi) together with Segger Studio...
I combined the BLE UART and SPIS Peripheral example of SDK V17.0.2 to receive data from a microcontroller using SPIS protocol in every 32 milliseconds and send it over through...
Hi Sir,
nRF Connect: v3.6.1 NCS: v1.5.0 and use original example to build code, Net core: hci_rpmsg example Application core: peripheral_uart example
H/W device: nRF5340...
Dear NCS experts, The development system is running:
Ubuntu 21.10
nRF Connect SDK (btw., where's can the installed version be seen?)
VS code (1.62.1 - in portable...
Good evening,
From testing my Nano 33 BLE , I've discovered that the following settings are reversed with respect to "High" and "Low", i.e., LEDs light up for Low, and turn...
I need to interface my sensors by using twi. Here one of my sensor is smbus compatible. For I2C, I need to read acknowledge from sensor. So i need reference or samples to...
I have update my thingy91 with thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex and mfwnrf9160120 as I was not longer able see anything in nrfcloud.The
Thingy91 does not connect...
Hi team,
i first of all want to thank you, for your support and help so far.
I have some questions regarding the values that are been given by the AT command %CONEVAL...
I have two 10056 52840DK（one load nRF5_SDK_17.0.2_d674dde/examples/nfc/record_text,
another load nRF5_SDK_17.0.2_d674dde/examples/nfc/adafruit_tag_reader）
Keil5 s140 test...
HI,
I have two DK10056 52840（one load ble_app_hrs_nfc_pairing ,another load pairing ble_app_hrs_nfc_c）
i using Keil5 SDK17.2 s140 test NFC pairing. I didn't modify the...
