Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
Hello,
I am just curious wether there are any specific recommendations or requirements for the package-sizes of capacitors/inductors listed in the BOMs of the nRF52840-reference...
Hello,
I am working with the latest version of nRF52 SDK 13.0.0, when I was implementing my own bootloader application, I tried to start an app timer in my code to invert...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
We have an application using SDK for Thread 4.1. The application requires sending large custom commands over CLI.
We increased the size of NRF_CLI_CMD_BUFF_SIZE in sdk_config...
Hi, I am using the nRF connect app to test the BLE function on my code. I am able to scan the device and Service UUIDs just fine. However, when I click on the "connect" button...
Hello,
I have been trying to implement the tinycrypt ECDSA algorithm for our product. I had sampled the implementation in a sample project with ECDSA being the only implementation...
Hello I am working on an application which is based on the ble_thread_dyn_mtd_coap_cli_pca10056_s140 example. I then used the ble_app_rscs example so that I could add Bluetooth...
Would it be possible to be talked through the steps of setting up SPI with the nRF52833DK using the Zephyr RTOS? I am new to the Zephyr RTOS and have so far been unable to...
Dear BLE mesh experts,
This is how the provisioning screen of my Android app looks:
The intention is to enable the user to provision various unprovisioned ble mesh devices...
I am reading through the code and would like to understand the following macro
#define DRV_RTC_INSTANCE(id) \ { \ .p_reg = NRFX_CONCAT_2(NRF_RTC, id), \ .irq = NRFX_CONCAT_3...
Hello!
In the description of the usb module, I found the registers: NRF_USBD-> DPDMVALUE, NRF_USBD-> TASKS_DPDMDRIVE and NRF_USBD-> TASKS_DPDMNODRIVE
" State D+ and...
