I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi Nordic,
I have old NRF52832 product which is developed by SDK11.0. The bootloader start address was set to 0x79000. Now We want to upgrade the it firmware by using...
Hi,
i'm using BLE MESH 3.0 Light Switch Example code. i want to send Light on-Off command every 2 second Timer base instead of Button press.
i got an error below.
Hi,
I am trying to develop the interactive_pyaci serial interface so that it can restore itself once it has been closed.
To do so it would be useful, once the db is loaded...
Hi,
Current github repo of IOS-nRF-Toolbox doesn't support X-code 10.2. Is there an update coming or is there a work around so that we can build app for ble-uart application...
I have the following issue: We are using the nRF9160 to track moving objects. Accuracy is of no importance, but battery life is. We experience the GPS accuracy as high, but...
Hello,
we've created a custom board with nRF52840 chip. The problem is that the device will not try to reconnect in a loop as it does normally in the examples. The function...
I am trying to get JLinkRTTClient (v646h) working on Ubuntu running in a VirtualBox 6.0 VM on Windows 10 host. I am using nRF52840 DK v1.1.0. I followed the guidance here...
Im using PCA10040 nrf52832 to measure light intensity with photodiode,
im using SAADC and SPI example to measure values but im not able to see any changes on UART as light...
We use the app button library to detect a change in position of three switches with the following configuration.
If the following sequence of events occurs,
1. Press...
Hello Nordic DevZone,
While trying to recover nrf52832 chip using command nrfjprog -f nrf52 --recover, I received the following error: Recovering device. This operation...
Hi ,
The following problem is happening in my case with old android devices. I found your answer from other thread.
"The phone first sends a LL_VERSION_IND and then it...
Now I use sdk15.2.0 hrs project to add the spim.
the mode of the spi is timer+ppi+spi.
question:1.I can't enter the led_timer_handler on time;2.I can't get the right data...
Dear All,
I am trying to use the external crystal as the source clock of the softdevice, as well as of the rtc. I am not sure if all this is possible and because I am...
Hello, I am trying to use PWM in the simple coap client example. Unfortunately the PWM is not working, I do not get any signal on the output pins. If I remove the line with...
I am currently involved with a project using the nrf52840. Page 96 of the Product Specification document (4413_417 v1.1) shows the electrical specifications for the HFXO....
