I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi !
I have been working on Rhydolabz R305 Biometric sensor using Arduino and I have completed with it . Since this sensor has very low Flash memory to store the Fingerprint...
I have a suggestion for an additional feature to nRF Connect for Desktop:
When doing DFU with a zip package that contains a bootloader + softdevice -combo and an application...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Hi,
I have a pretty extensive nRF52832, SDK14.2, freertos project built and debugged using Keil MDK.
I'm trying to port this project to SES and experience some problems...
Hi,
LED is on when the button is pressed. Press the button again and the LED off. I want the Turn the LED on as long as I press the button. Turn off the LED when I stop...
Hi there,
I've already implemented a custom firmware for nRF52832 with SDK 15.0.0 and S132 v6.0.0 which uses both advertising and scan operations, and now I'd like to use...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I'm wondering why the pairing request sometimes shows up in the notification bar and...
Hi,
I am using nRF52832 with sdk 15, freertos.
I need to implement the following logic:
1. Get into low power mode, while keeping a timer running.
2. Every 10 mins...
I was using NRF52832 and s132 v6.0.
I have Android phone's IRK and I have added the Android phone into the identites list manually.
After doing the direct advertising...
In the NRF52-DK user guide, the following is stated:
Important: When using ANT/ANT+, the 32.768 kHz crystal (X2) is required for correct operation.
However, I could...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
Hello,
BLE MESH 3.0 Light Sw Example code just I have add APP_TIMER_MODE_REPEATED and its work fine.
Case 1:if I print string Or LED Toggle Based on timer its working...
Hei there!
First of all thanks for all the great work here!
My question is:
In my application, the final device will have 4 pogo pins.
Two of them are for power, the...
Hello All,
Hello all,
I am working on BT832A in which nRF52810 is used and i used segger studio for programming in windows 7. I am refer nRF52 SDK 15.2.0. And i am load...
