I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi
Firstly i am coming from 8 bit world(PIC and Arduino) and not so good at c programming. ( just writing all code in main and sometimes using function) (not even use pointer...
Hi.
I want use the synthesized LFCLK.
But sdk_config.h has the 3 items about LF clock source
- NRFX_CLOCK_CONFIG_LF_SRC
- CLOCK_CONFIG_LF_SRC
- NRF_SDH_CLOCK_LF_SRC...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I have some doubts about bonding,the parameter about PM_PEER_ID_N_AVAILABLE_IDS and...
Hi, latest SDK15. Running BLE_UART example on devkit evaluation board.
Budget Lenovo Android phone will discover BLE device.
iPhone X will not discover BLE device...
How to configure a node for control model. I have used light switch on/off template to implement a control mode but i i don't know how to make a control logic for client....
Let me preface by saying I'm pretty new to working at this low of a level. I'm running a pretty simple program that is toggling a pair of pins once every half second. The...
Hi,
I'm using SDK 15.2.0
I need to measure the voltage in AIN3 and I would like ot know what is the difference between ADC SAADC and SAADC legacy layer.
The system...
Hi,
I am trying to set up SEGGER Embedded Studio for ARM and run secure_boot project.
All the time I have "Project load failed Reported error: solution load command failed...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52. And I am using Segger Embedded Studio to build and debug the code. But the IDE is unable to find the libraries...
Hello Everyone,
I am using nRF52832 with Softdevice S132 v5.0 and SDK 14.2.
I have been using ble_app_uart application as a starting point with SES. What i need now is...
Hi all,
I'm trying to learn more about the pairing and bonding procedures in the SDK. I connected one nRF52480 DK to my computer (running Ubuntu 16.04) and let nRF Connect...
Hi everyone, I have a nrf51822 Bluetooth chip that control a stepper motor, this Bluetooth chip can be powered by a maximum voltage of 3.6V, but I need a higher voltage for...
I have a split bluetooth keyboard that is using this firmware for the nrf51822 chips: github.com/.../mitosis-bluetooth
The general idea of the software is that the right...
