I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Installed nRF5_SDK_15.2.0_9412b96 and nRFGo Studio. nRFGo Studio fails to recognize the nRF52840 DK board. Screen like this:
It sees and correctly identifies the Segger...
I am trying to do things like
get the current date and/or time
configure a socket
activate a socket
Usually I use commands like
at+cclk
at+csdf
at+ctzu...
I am following the Thingy:52 "Compiling With Keil" instructions provided in the following link.
nordicsemiconductor.github.io/.../firmware_compile.html
However, I get...
Hi,
We have released multiple products with the NRF52832 chip with SDK's ranging from 10.x to 14.x, quite successful so far.
However, one part that is lacking in my opinion...
I have been struggling with getting nrfjprog working on CentOS 7.x. Each invocation results in the following error due to the version of glibc used to link the nrfjprog binary...
Hello!
A quick question about how to shutdown unused RAM on the nRF52810-CAAA?
We're not using any of the Soft Devices. Our code is pretty tiny. Map file attached.
We...
Hi,
I want to read data from my ble UART (NUS), to do that I implemented the NUS service and registered the onDataWritten callback (which is the MBED equivalent of the HVX...
Hello:
If we are to use the nrf9160 in a production product, what additional certifications are required? For example, if I purchase a Telit cellmodule, I still have to...
Hello All,
I want the DFU service at the application level, not at the bootloader level. Means I have to build a very simple bootloader but I want DFU service at the application...
Hello nordic:
nrf52832 how to control pa, i use this functio pa_lna_assist(). This function is the solution on BBS.this used for s132,but i use s332.the ble is ok,but the...
As per description, I don't understand how to make a dfu package that writes the whole MBR+Application range and doesn't use a SoftDevice, for example out of a hex file such...
I'm using SDK 15.2 and trying to set up a USB mic class. I am having trouble getting the SOF audio interrupt to fire.
I initialize the app_usbd module with the configuration...
Hi
I would like to know that is there any Blue tooth low energy relay like RFID tag , which can detect bLE only and can trigger a circuit. It should have small form factor...
Hello everyone , i have noticed that the sniffer can pick up the the packet from the same channel twice.
According to the Bluetooth 4.2 specification, the advertisement...
Hi all,
We were developing our application using nRF52840 and later decided to change to nRF52832 considering our hardware constraints. nRF52840 has 16 bit counter for EasyDMA...
