I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm able to successfully use peripheral/uart example to read the data from GPS module. I achieved the same by setting baud rate to 4800, and connecting rx and tx of GPS to...
Hi,
Question about FOTA (firmaware upgrade over the air).
I know that nrf52832 has 512 kB of flash, and the ble stack( softdevice ) has 136 kB , and the bootloader has...
Hi,
I put my NRF52 to sleep (POWER OFF mode) and configure it to wake on GPIO port event like so:
This GPIO is set up on a reed switch. Occasionally, the NRF52 will...
Hi
I found a strange issue on nrf52832. And I use nRF5-SDK-v13.1.0 .
When I assignment P0.7->SCL & P0.6->SDA, the twi function not working. But I change the assignment...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
Hello everyone, I am a beginner in the use of Nordic Thingy: 52. I would like some help trying to reprogram the Nordic Thingy module. After a programming error of the Thingy...
HI,
I am unable to communicate between a SDK 8.0 based nRF51822 sender and SDK 14 based NRF52832 receiver.
The data rate of the SDK 8.0 sender is 250 KBits/sec, whereas...
Hi,
Can someone help me with question on SPI?
What is the difference between SPIM and SPI? They seem to have different clocks
Also in the SPIM section, the frequency...
hi,
I need to know how to use "power on reset". From the reference document, I can understand BOR and POFWARN. But the POWER ON RESET, I could not get any idea.
1. POR...
i have project with nRf51822 and uart. i use uart fifo in Uart_app_ble example sdk11. now i need disable or enable Rx, TX.i tried this function :
NRF_UART0->TASKS_STARTRX...
Hi,
Has anyone successfully used semaphores/mutex implementations of FreeRTOS?
The code I am working on is based on the FreeRTOS HRS SDK example. I am looking to add a...
Trying to compile using the on-line Mbed compiler. I keep getting cannot find "nrf.perhiperals.h", and I cannot locate it either.
Possible someone can point me in the right...
Hello.
I'm using Tielen Marjle STM32 library for nrf24l01+ ( https://stm32f4-discovery.net/2014/06/library-17-nrf24l01-stm32f4xx/ ) which worked great till now, when I...
