Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi
nRF54L15-DK QFAAC0, ncs v3.4.0, project path: ncs\v3.4.0\zephyr\samples\boards\nordic\system_off
After compiling and flashing this example, the power-on reset (POR...
I am using Windows 11, NCS v2, VSCode extension, under WSL2.
What I want to do is build a UF2 image of my zephyr application and be able to drag/drop it onto a bootloader...
Hi Nordic team,
I am testing Bluetooth Channel Sounding with the official samples and would like to ask about an unexpected behavior I observed.
Setup:
- NCS v3...
Hello Nordic Support Team,
We are developing a custom product based on the Nordic nRF54L15-CAAA(R) SoC.
Our project requirement is to use the nRF Connect SDK Bare Metal...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hi Nordic team,
I am investigating an abnormal ripple issue on the nPM1300.
Power configuration
The power path of the LDO is:
VBAT / VBUS → VSYS → VINLDO → LDO output...
Hi Technical Support, We are using nRF54 series with NCS v3.0.0, and we have encountered a low power anomaly as described below: Configuration: SoC: nRF54 series NCS: v3.0...
Hi,
I would like to know how to ensure that AP-protect is disabled for application based on 17.1.0 nRF5 SDK.
I've understood that the procedure is:
1. recover the device...
We are designing an nRF52840 (Ebyte E73-2G4M08S1C module) into a battery-powered wearable, USB device only, Full-Speed, sink-only Type-C with 5.1 kΩ Rd on both CC pins. We...
I'm starting an investigation into Bluetooth LE Channel Sounding using the nRF54L15 Tag, nRF54L15-DK, and nRF54LS05-DK.
For the intended product, I need approximately 150...
We have a product in the field using the NRF9160 and AWS IOT MQTT from NRF Connect SDK 3.1.1. It is always connected when awake (power cycle controlled by an external micro...
Hello,
We use the nPM2100 EK for getting familiar with nPM2100 for its potential use in our project where we aim to use single AAA battery for powering it.
Our usage profile...
