Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
hi,
i am using nrf51422 ble_app_uart(sdk 12.3.0) example
i am receiving a string through app_uart_get() function, i want to compare it then i have to send some predefined...
SDK15, s132 6.0, nRF52832
Hi!
I need to know before connect on the central side (from advertise data), that this piripherial device has already bonded.
Is it possible...
I'm having some trouble setting up 2 transports (BLE + USB CDC ACM) with the secure_bootloader example. The changes I made were:
- Increased flash size for code space in...
Hi,
It's my first design with nRF52840 (I have make multiple design with nRF51 et nRF52 without problem).
I use SDK15.2 and BLE_peripheral_blinky example without modification...
I'm using nrfjprog to develop a production functional tester for an nRF52840 based system. Everything was going well in testing, but when I moved the hex file to be loaded...
Hello
I have a problem with ADC measure and accuracy.
I want to read a voltage (U_BAT+) between 2.5 – 4.5V with an accuracy of < +/- 50mV
I have two scenarios. ...
Hi. I want to output numbers to tm1637 display with nrf52832. The existing library is dedicated to Arudino, so we will contact you to change it for nRF52. (Existing library...
Hi,
I am having some task which for which i am using GPIOTE, PPI & TIMERS together to achieve and in SDK 14.2, the over all power consumption of my board is 10u which...
I am trying to integrate DFU into ble_app_uart example.
I am using nrf51422 board, sdk v10.0.0, soft device "s110_nrf51_8.0.0_softdevice.hex".
I have made some changes...
I'm trying to use Pin 0.21 as SCLK in the SDK15.2/examples/peripheral/spi/pca10056/blank/ses.
The example works fine with CLK on pin 3 (default) and on pin 29 (just tried...
Hi,
I created nrf52 project on Segger studio. I'm writing directly registers.(not SDK)
It includes i2c,uart and adc, this part is working now.
I want to add SoftDevice...
Hi,
I'm using Keil development tool.
The original bootloader start address is 0xE6000 and new bootloader start address is 0xE5000.
When I update to new bootloader, it...
hi...
What are the things I can check if I can't find my nRF51 upon scanning for BT devices? I am using nrf52832 and can successfully program the device via a Segger J-Link...
Simple and perhaps stupid, but important for me: the reports of detected devices I see in nRFConnect (desktop or mobile version) are based ONLY on BLE advertising packets...
Hi,
I am experiencing problems with the app_error_handler function defined in app_error_handler_iar_c provided with the SDK V15.0.0.
If the function gets called when debugging...
