Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Im on an nRF52832, using the BLE Mesh 0.9.1 alpha release
I've followed the DFU Quickstart guide, and have been able to DFU the app_green_s132.hex, which is the prebuilt...
hi,
i am using NRF52 custom board. i want to provide serial number to each board, which i want to read or write any time using my firmware. if i erase the bord it should...
Hi,
I have a BLE nano v1.5 from RedBear. I want to use s120 SoftDevice developed for the nRF51822 and for what i've read this is not available for programming with mbed...
Hello,
I have migrated from SoftDevice S130 2.0.1 to SoftDevice S132 3.0.0 and found one mismathing in ble_gap_evt_connected_t structure.
There is absent an own_addr...
Hi,
Is it possible to make pairing without the peer/device/bond manager? I am using SDK 12.3 on NRF51 and/or NRF52 and would like to get it to pair with a certain device...
Hi,
I'm using nRF52840 and S140 based on the ble_app_hrs_rscs_relay example. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu...
Within a buttonless DFU application should nrf_dfu_flash or fstorage be used to erase and write to flash?
SDK 13.0.0 - Soft device s132_nrf52_4.0.2_softdevice running on...
These messages below appeared when I built bootloader_dual_bank(sdk11) in the eclipse.
'Building target: bootloader_dual_bank_s130_sdk11.elf'
'Invoking: GNU ARM Cross...
I want to have blinky orange led,
0 mean on, 0x8000 is off, right? and why??
I have no idea what's 0x8000 mean!
so if I want have orange(full-R and half-G), how can...
I'm trying to debug my UWP Central app, which interacts with our device based on nRF52/s132. What I think I'm seeing with my packet sniffer (the nRF51 sniffer, incidentally...
I have set the
advdata.include_ble_device_address = true
in advertising_init function. However, the mac address data is not shown in mobile APP.
Is it due to the fact...
I would like to include multiple p_chunks in one record. How do I do this? I've only seen examples with one chunk per record, but fds_record_t.data has a field called number_chunks...
Hi, I am considering using nRF24L01 for a project, and I wanted to use one single transmitter to send data to various receivers (more than 6).
I have found some information...
plss, help me . i can flash other examble nomarlly . But when i tried to flash ble_app_uart to nrf52832 seem previous program still works and new program not flashed yet ...
