I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello,
I'm transitioning from the old SDK to the ncs, and have been through the nRF Connect SDK Fundamentals and Bluetooth Low Energy Fundamentals courses.
With pairing...
EDIT: Sorry to be posting a lot about my LIS2DH12 problems lately, as I'm advancing somewhat while I have open support threads. Newest thread is here: In preparation of this...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
Hello, I am going through the Bluetooth Low Energy Fundamentals provided by Nordic.
My nrf 52840 dk could function fine after lesson1, but when I flash my board with the...
Hi,
after upgrading to NCS v2.7.0, I have some trouble with an increased sleep power consumption of our device when I use Zephyr's gpio-keys for the button input.
I was...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
We have a product based on the nRF52840 which uses the GC9A01 display driven using SPI on battery power. The device also functions as a Bluetooth connectable so it is normally...
Hello DevZone,
I am using a nRF52840 with sdk 17.0.2 with Windows 10
I am trying to setup a connection to my Windows PC but I noticed data fragmentation and a queue...
Hi,
For the SoftDevice controller, how can I send LL_MIN_USED_CHANNELS_IND messages? Is there an API for this, or what scenarios trigger the sending of this message? Thanks...
Hi,
MCU: nrf52840
SDK: nRF5_SDK_17.1.0_ddde560
I am facing such an issue, sometimes after the device's OTA success, and then I would like to upgrade to another version...
Hi Nordic Team,
I am using the nRF52840 microcontroller and have interfaced a modem with one of its UART modules, as my modem communicates with the Nordic chip via UART...
Hello,
I'm measuring the power consumption on the Thingy:53 using the Debug and Current measurement board. Initially I was measuring the current of the battery VBAT given...
I have been using the VS Code extensions for setting up and building projects. Sometime yesterday build times went up from < 20 seconds to 10+ minutes. It looks like it's...