Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Dear Sirs:
We use nRF52810 as the key chip in our product, however, we need it to be central or peripheral based on user's option.
So, we would like to apply softdevice...
Hello!
I am currently working on doing the smp_svr sample:
I have done these commands so far (on created from sample application):
west build -b nrf52dk_nrf52832 -d...
Hello DevZone,
I am using Segger embedded studio with multiple build configurations for the two chips and I am having some issues to get the program to compile my nRF52810...
I have tested the sdmmc driver yesterday with both, CS Pin tied directly and via an external i2c port expander. TCA6408A.
Worked like charm, but today I wanted to to some...
We are using nRF9160 chip (in own custom board), SDK 1.9.1 board with "serial lte modem" firmware. We are unable to get coordinates using AGPS. I suppose this is due to the...
Hi!
I am going to use nRF52832 in a new product and wondering whether should I base an application on the new or the old SDK. I have to take into account support for DFU...
Hi,
recently I got Thingy:91 (board info - PCA20035 1.4.0 2020.22),I've updated it to the latest firmware as per instructions. So far so good. Then I started playing around...
I tried to create/ open a project using nRF Connect in SES. The error appears as shown in image. While the file exists as shown in the second image. Why, such error and what...
Hi,
Basically, the setup of the mesh network is as follows,
There are END NODES based on sensor server model.
There are RELAY NODES based on the sensor client model...
Hi,
I am using Zephyr3.0.0 to validate AOA CTE sampling.
Firstly, a s below is the official data format. Nordic Semiconductor Radio peripheral provides 16 bit wide IQ...
Hi,
I am able to successfully build and flash the Matter Light Bulb sample onto my nRF52840 DK.
I am now getting ready to configure the firmware for use on a custom board...
Hi,
NCS1.9.1,nRF5340DK, VSCode，
see code, timer_lms==1000 spend 1000ms
but if start i2s
i2s_audio_init(); //this line will Slow down the time
timer_lms==200 spend...
When i try to use SES to build my project.there is error.The enviroment i confige as descrblied. them i use toochainmanger in nrf connect tools,the error is as the same as...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
