I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
In "nRF52832 Product Specification v1.4, it recommends 32MHz with 40ppm as below:
as the question mentioned above, can I use one with 10ppm?
thanks
best regards...
Hi,
I am getting assertion failed error when putting the device in System off. Could you please help me understand why?
Below in the code where the error happens:
...
I'm working on modifying the ble_app_uart pca10040_s132 to send strings stored in flash memory over BLE to the nRF connect app on an iphone. From what I understand the uart_event_handle...
Hi There,
I m trying to use the xxxx\SDK's\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\peripheral\spi with the nRF52480 Dongle and I already had applied the...
Greetings
I have an NRF51422 QFAAEO running S210 Soft Device version 3.0.
I have written a Bootloader application that uses Ant-FS as the upload mechanism. During testing...
Hello everyone,
is it normal behaviour to lose data on UART reception when BLE scanning and advertising both are active?
So far I didn't lose serial data if I just run...
hi all.
I am trying to change number of data packets in one time interval.
I don't know the senario to change it.
For first step I wrote this code to change the quee...
Hi,
I want to write data to the Flash memory of my Nordic thingy 52 board.
When I erase flash using API ret = fs_erase(&fs_config, fs_config.p_start_addr, 1, NULL); return...
Hi, I hope you are fine first of all
I'm have a PN532 module. I want to write and read data from that Midare card.
I started with the example Adafruit tag reader. when...
When i program our new nRF5340 based radio boards the program returns Device Protected for both cores on completion. It is also impossible to debug the board as my segger...
Hello
When we want to establish a pairing from the connection, I see in your examples that you call pm_handler_secure_on_connection() which calls "conn_secure()" when the...
Hi everybody,
is there an issue for using the twis
module and bluetooth at the same time?
I have problems merging the example
projects (ble_app_template and
eeprom_simulator...
Hello,
This is a strange problem and I do hope I am missing something. There are two bootloaders in the examples/dfu section for a particular transport - with debug and...
Hi,
I want to add manufacturer specific data filter in nrf_ble_scan module.
I have gone through the nRF SDK. But the manufacturer specific data filter related fields...
Hello, I want to scan all ble devices present near by nrf52-dk and process the data in my application. I am unable to find the scanning ble device code in nrf52 sdk. I am...
