I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have managed to upload data from nRF52832 using nRF9160. I upload the data as tempreture sensor (although they are just values in mV), and my interface at the nRF connect...
I have extended the Template app in nRF Toolbox. When my app runs in the background on an Android 8 (only) device and I try to connect to the peripheral, I get this error...
Dear support,
The build of the asset tracking application is not working
Below the copy and paste of SES buildlog
Building ‘zephyr/include/generated/driver-validation...
Dear Team,
could you please share some info on the Content of the nRF9160 Chip when it is shipped from Distributor? or a Sample?
What is the Content of it? is it empty...
I entered Reset mode and got a blinking led. I want to exit this mode but when I unplug and reconnect USB, led does not light and port does not show.
There must be a simple...
Dear all,
For EMI/EMC Test, we need the USB UART CLI functionality for example "Radio Test",
could you tell us how to implement it or any example can do that?
Thanks...
I am using 3 axis LIS2D12H accelerometer interfaced with NRF51832 with SPI interface. The sensor has sampling rate from 1 HZ to 5.376 KHz which is happening at sensor only...
Please, share the firmware of the board nRF9160-DK PCA10090 version 0.8.5 , which is flashed into a new board. The firmware that I received using the instruction ( https:...
Hello,
I am using NRF52832(WLCSP package) and nRF5_SDK_15.2.0 for the product.
I also use IAR Embedded workbench 8.32.1 as IDE.
Few hundreds devices are assembled...
Hi,
I'm trying to figure out how to ping a specific IP Address from the nRF9160 via AT Commands. I can't seem to figure out how to do a simple ping to an internet server...
Hello! Board nRF9160-DK. Compiled and uploaded the project asset_trecker (merged.hex). The LTE Link monitor shows a cyclic reboot. LEDs do not blink. where is my mistake
Sorry,I want to know whate is the different between BLE_UUID_TYPE_BLE and BLE_UUID_TYPE_VENDOR_BEGIN, the Device name will become N/A when I use BLE_UUID_TYPE_VENDOR_BEGI...
Hi,
I'm studying the example about the nrf_crypto for implementing asymmetric encrypt and decrypt function.
The suggestion on the Dev_Zone is to use the share key to symmetric...
Hi,
Is there a possibility that the order of the responses can be different with respect to the order of the requests?
We check for the success status of the APIs sd_ble_gattc_read...
These two options in nrf_mesh_config_app are arbitrary for me if I don't understand how they should be sized.
From the documentation of the MESH SDK 3.2.0:
ACCESS_FLASH_PAGE_COUNT...
