I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
We are using the SPIM driver to support a propriety 1-wire protocol used by a TI LED driver (TLC59731). To do this, we're using the MOSI pin exclusively and, for it to work...
I have been trying to get 125Kbit and 500Kbit coded phy wokring by directly using NRF_RADIO API (no softdevice in use). I have followd for example these instructions, but...
Dear all developers,
I'm currently studying about nRF52832 SoC and prepare to develop low current BLE device.
Before starting, I want to know about idle current consumption...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello,
I post a question last day, and I can not open it any more now, it always saying "Content is under review"
Even the question has been replied to:
The link:...
I don't use SoftDevice. If I initiate flash partial erase process, my understanding is that the system will do smaller portion of erase, suspend, erase again, until the whole...
I'm developing an application on an nRF52832 revAA that logs data coming from the app_uart module. It logs this data to an SD card using the fatfs library; the code is more...
I need to implement a uint64_t counter that increments every microseconds that I can then read.
I tried to use the timer API and increment the counter in the event handler...
Hello,
So I am aware the nRF52832 utilizes the ARM cortex M4 microprocessor and has 32 configurable GPIO, but I'm failing to find how to access the registers controlling...
Hey I am trying to setup UART on my Thingy52 but when I’m trying to compile my project I getting this error message:
I am using GNU Tools ARM Embedded 4.9 2015q3 for compiling...
Updating all components with the nrf9160DK, I am unable now to run the LTE/BLE Sample. I built all the prerequisites, secure-boot, hci-uart and lte/ble sample however, the...
I am very new to Nordic boards, so my apologies first for my ignorance.I recently bought Nrf52840 boards and I want to build a very simple Bluetooth mesh application but I...
Hello All,
As we all know Segger Studio is not supported by SDK12.3 by default. Porting to Ses is easy and help is available but it is for basic programs. if we want to...
sdk version:15.2.0
sd version:6.1.0
platform:pca10040
I have inited three saadc channels , I want to close the specific saadc channel ,but error occured .
The...
