Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi all
I am doing multiprotocal from sdk15.3 and I am trying to add nrf_gzp.c, nrf_gzp_host.c, and nrf_gzp_host_nrf5x.c in to the project
after compile successfully and...
I was wondering, is it possible to suspend/resume flash operation in nRF52840 (internal flash)? Like flash erase suspend, and also flash write suspend/resume?
Thank you...
Hi,
Might be a silly question,
but is there a gattc equivalent of the "BLE_GATTS_EVT_HVN_TX_COMPLETE", ie a similar/equivalent event that gets generated when a central...
Hey, I am working on the proximity application on nrf51 DK. How can I get the bsp_event_handler to get triggered on a button multi press (such as pressing button 1 twice rapidly...
Hi,
Do you have support for mobility in Cat-M on your nRF9160? This is usually done in RRC connected, but i'm wondering if you are able to support it in eDRX as well?...
Hello;
We are developing a project. And there must be three features in our project.
1) Should scan and transmit beacon at the sametime
2) Chip should read and write...
How can i read advertisement and not connect? I would like to do some checks on the advertising data within BLE event BLE_GAP_EVT_ADV_REPORT and then decide if i want to manually...
I am trying to transmit a modulated carrier with a high duty cycle but it does not work
the same command works with the default duty setting (50%).
The cli freezes when...
VUSB current consumption of the NRF52840: We have a setup where the 5V supply to this pin has very limited current capability.
What is the maximum current which can go into...
The Problem: HardFault within sd_softdevice_enable. With HardFault breakpoint enabled, the debugger halts at address 0x8C8. With this breakpoint disabled, breakpoints after...
I having trouble setting power level above +4 dbm in my app based on the example "ble_app_beacon" using the PCA10059 nRF52840 dongle. I have updated the main.c with the following...
Hi, i'm designing a device which is based on nrf52832 chip and i need to add two IC on my board, the first one is the MAX8856 to charge the battery of my device and the second...
I want to execute timer interrupt at a certain interval, like 1sec or 5 sec.
I measured an actual interval of voltage change with oscilloscope, but the actual interval is...
Hello
i have nrf 51822 beacon and i need to setup beacon that he send out data and i scan it without connecting-read brcst data.
i scan microchip 4870 and other beacon...
What is the best method for attempting to recover from a stuck TWI bus after init?
I am currently initializing the TWI instance with .clear_bus_init=true but this only...
