Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I'm using nRF SDK v15.0.0. I have have added battery service using this online tutorial: https://www.novelbits.io/smart-ble-lightbulb-application-nrf52/ . The code...
I try to eddystone url beacon with advertise every 5 second. I changed
#define APP_CFG_NON_CONN_ADV_INTERVAL_MS 5000
upload code in nrf52832 module I used NRF connect...
Dear Sir,
I am working with SDK15, nrf52832 and softdevice s 132.
I am using ble_app_template with slight modifications.
Now it will advertise for a duration of 10...
Hi
I am using nrf sdk 15.2.0 for MEsh networking.(Mesh SDK version 3.3).
Hardware platform -nrf52832(pca10040).
Steps followed:
1. Compile and Run light switch demo...
Dear nordic,
I want to test Thread. I selected Thread Cli example for this. but i need to know something regard this. Iam new in the thread. from this example command is...
Hi, I am trying uart example now, not first time. I made it and check the receiving and transmitting data through ble last week.
The problem is it is not working now. Building...
When i am sending data packet from node a to node b why is b node relaying the message back and forth.It shudnt do that .
I just have 2 nodes in the current setup. Node...
I watched https://devzone.nordicsemi.com/f/nordic-q-a/33591/softdevice-s140-v6-0-0-how-to-set-the-channel-mask-for-different-channels
Does this work the same way in my situation...
I'm having a heck of a time getting the SAADC to just return one sample in a blocking manner using SDK 15.2.0
I'm pretty far along in developing a couple of nRF52840-based...
How many capture compares does each timer have on the nRF52810?
The documentation is conflicting. In the "Registers" section for the Timer peripheral in the data sheet it...
Some comparison charts I've seen from Nordic indicate that the standard is supported by nRF52840 only, but it is not clear if it can actually do it in the three bands specified...
Hello,
I have a peripheral based on SDK 9.0. I have tried to follow the peripheral proximity example to get bonding working with the app. The App is currently running in...
Hello,
Im new to the Nordic Ecosystem, and have been trying to set hardware uart with Nordic Thingy 52 with CP210x using the sdk13 uart example. I included the uart driver...
