Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Is there a working example with using gpio_dt_spec for accessing gpios?
I used the code provided from https://docs.zephyrproject.org/latest/reference/peripherals/gpio.html#c...
Hello, by usingnrf52832 DK and testing some examples i found out that the example peripheral UART was not going like I wanted to do. He is going to sleep mode after 3 minutes...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v1.0.1%2Fmd_doc_getting_started_how_to_models.html
Linkte verilen yönergeleri takip ederek...
Hi all, I discovered that if I get BLE_GAP_SEC_STATUS_AUTH_REQ while pairing, the device is basically useless until a new reset. I would be extremely grateful for some help...
Hi All,
I have a project which uses the zephyr shell, but I can reproduce the issue with zephyr/samples/subsys/shell/shell_module or any other sample making use of the UART...
uint32_t address = XIP_ADDRESS + addr ;
uint8_t * p_data = ( uint8_t * ) address ;
for ( int i = 0 ; i < len ; i ++ )
{
data [ i ] = p_data [ i ] ;
} The Pin of QSPI...
Hello,
I recently installed the VSCode Extension for nRF Connect and I am experiencing, what seems to me, strange behaviour.
Here's the steps:
I create a project from...
Hi
I modify the ble_app_uart_c example to support connecting multiple nus peripherals.Calling the new_cccd_configure(p_ble_nus_c, true) return error after nus_c discovers...
Hi,
I am using nRF Connect 3.9.1 and power profiler 3.2.1. I have noticed that if I have a measurement on-going and go away for a while (4mins tested while writing this...
Hi,
I am using an nRF52840 with SDK 17.0.2 and S140 7.2.0. I am running a scheduler based on app_scheduler.
I am trying to make my FDS implementation blocking as it...
hello ;
i am new for nRF52840 DK , i just want to learn how to use it , i need to deploy to bluetooth (ble5) on nrf52840dk to connect or send the data to esp32 , however...
Hi All,
Due to chip shortages we have to replace nRF52832 with nRF52810 in our design. Our application has to perform BLE scanning, but no other functionality of a BLE central...
My nRF is a central and the iOS device is the peripheral. the nRF connects to the iOS then checks via pm_conn_sec_status_get() if pm_conn_sec_status_t is encrypted, if not...
