Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
refer an example for long lange demo in sdk.
i have found this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo but in this nrf52840 boards are used...
Hi, What we would like to do is to store the firmware on one nRF52 MCU and do the DFU over BLE to the other nRF52 MCU. This means that the first nRF52 MCU needs to connect...
Hi Nordic,
my BLE peripheral with the nrf52840 and sdk 15.3 with s140 restarts if not connected after 180s. I assume that the reason is the .config.ble_adv_fast_timeout...
Hi,
I am trying to create a mesh network using nrf52832 for RGB lights. I am using nrf Connect SDK to build the project. Is there any sample code for RGB that can be integrated...
I have found that you cannot update MCUBoot unless you also have the NRF Immutable Secure Bootloader, If i have this then i cannot update the Immutable bootloader.
Is there...
We developed a ble hid mouse using ble_app_hid mouse example. When our mouse used in MAC os scroll wheel function is not working as expected i.e. when we scroll there is only...
Hi, We have an issue with custom devices in the field that have nRF52811, with s112 programmed. To sort out our issue we need to connect to the nRF52811 that is an advertising...
Nordic's BLE page ( https://www.nordicsemi.com/Products/Bluetooth-Low-Energy ) says the nRF5340 is the "ideal choice" for LE Audio. I can't seem to find any information on...
Hallo,
my nRF52840 and my nRF24L01 are receiving the same data in proprietary radio mode.
Several nRF51822 are sending mixed up data.
Within the nRF24L01 - radio Interrupt...
Hi,
I am completly new in nrf52, nrf-connect and zephyr environment.
I need to configure pwm channels that wont be used to drive led...
Most of thing is undestand for...
Sending a PSK like:
AT%CMNG=0,42,3,"1r0nm@n"
should result in failure, as that is not a valid hex string (as documented in nRF91 AT Commands). Currently this results in...
Hello,
I am trying to run the CCS881 sensor sample in my nrf9160 board. I have made changes to my project config file and main.c file as mentioned in
https://devzone...
I need to compare two ble_date_time_t structs to figure out if one is later than the other. So basically I need to check if rtc_datetime > expiration_datetime. Both rtc_datetime...
I plan on writing my own service (similar to NUS) but prior to that, I'd want to use all the existing APIs for initializing the GATT and BLE stack at least
I'm calling the...
Hi Team,
i have trying to create multiple serial port with debug log enabled in the sdk code sample but when i am going to init log_init a long with any UART / SERIAL...
