Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi I have recently started to use nrf5340dk for a 'pet' project. I have developed some code for both app and net.
Then I started to note have some trouble on the serial...
Hello world :-)
As there is no Issues section in sdk-nrf I will post my question here. After west update I cannot build my firmware anymore. I am using v2.6.0 Zephyr and...
Hi,
We developed a code using Fanstel nrf52832X BLE using serial UART command to control, receive data and send data.
The softdevice is s132_nrf52_6.1.1_softdevice.hex...
I2C burst write for nRF5340 at 100kHz is failing with a reply of -5. (Trying to use the BMI270 drivers sample, it will fail during reg_write of the configuration file)
Reading...
hi
I have nRF9160 dev kit, which I am using in a LAB with a private LTE SIM card, which has 99920 PLMN ID.
The network supports Band 3, and NB-IoT is configured as an...
Hello everyone,
1st of all, thank you for taking your time to have a look over my "problem".
I have a device that I am working on, that acts as aperipheral, it is...
I modified, My application's bdaddr is set public device address. secure bootloader's bdaddr is set same public device address.
When run DFU on nrf connect for desktop,...
In my application, I am unable to read back the publish address which was configured during initialisation through mobile.
Please suggest any APIs.
Device: nRF52832
...
HI
The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" and I find a question that is: for all thread programs, add nrf _ delay_ ms () function in while (true) will affect...
I use a sample in NCS1.5.0 to start my project . but examples in NCS1.5.0 are single ble service .always like these: bt_conn_cb_register(&conn_callbacks); bt_enable(bt_ready_cb_t...
Hi,
1. I see the following differences between VDD1 and VDD2 descriptions:
nRF9160_PS_v2.0 P385
2. What are the differences between VDD1 and VDD2 features?
Thank...
Hi all,
I am trying transition from SDK 15.0 to 17.2 and having a branch instruction to itself (an infinite loop) which I think has something to do with the adjustment of...
I would like to create SPI clock timings using the following documents. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fspim.html&anchor=topic
1. CSN...
I'm trying to figure out a strange issue with GPS. We have a pretty well debugged and stable system that we're adding some features to, mainly GPS. We're on SDK 1.5, using...
