Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I would like to use MAGPIO0 , 1 and 2 as 1.8V inputs. I've read through the documentation, but can't find any way to assign pin numbers to these (I'm using Zephyr), only that...
Hi,
First i want to know what is the relationship between connection interval and GAP Event Length.
In one test condition I configured as:
connection interval = 7...
Hi Experts,
We are developing application on nRF52840 based BLE 5.0 module i.e. BMD-340, in short we are integrating the BLE in one of our existing product & upcoming...
Hi Nordic Team,
I'm working with Nordic NRF52832 BLE development Kit. Currently, we are working with DFU Secure bootloader. In this bootloader, we tried the button pressed...
Hello everyone, I am running a code with uart i2c interruption and power management but I have this error : nrf_pwr_mgmt.c:78: undefined reference to `__start_pwr_mgmt_data...
Hi,
Does Nordic have a network-steering function that attempts to join networks on all channels? We will not know which network channel the sensor needs to join ahead of...
Earlier (couple of months) I was working on the examples/peripheral/ppi example in SDK12.2.0. I converted the Keil project inside pca10028/blank/arm5_no_packs to a Segger...
Hello,
I am trying to reset the Zigbee network configuration on my End Device when the user press on a reset button for a long time.
I don't want to restart the product...
Hey.
I have a GPS chip which uses 57600 baud for its rx pin, and 115200 baud for its TX pin.
I need to switch between the two baud rates, and also some times connect to...
I'm using nRF51822_xxAA , with SDK12.3.0 and Softdevice S130 v2.0.1 on Keil V5.29.0.0. And as a central I use Redmi 7A phone with Android V10. I want to sample ADC @ 200Hz...
Hi，all:
There is a question when I run usb_msc example on nrf52840DK(sdk17.0.2)，I do as following steps,
Then,after I press button 1 for serial times,I found there are...
I want to get started with nRF52832 in Arduino. I have a Ebyte development board with E73 module containing the NRF chip.
The hardware is quite similar to Adafruit NRF52...
Hi,
Hope you are doing well!
I am trying to do Buttonless DFU on our own Android APP. I have finished programming on nrf end and succeed doing DFU on 'nrf connect...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag) it is showing following error. could not fetch memory size of target devkit...
Hey all - I'm new and trying to connect Thingy91 to nRF Connect V3.6.1 for the first time. When I open the Programmer app I only see "No devices available" in the drop down...
