before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I am working with signled door sesnor and it supports ZigBee 3.0 as it has an install code and mac address on the side of the sensor in the form of a QR code. When I run the...
We are using the latest pc-ble-driver with SoftDevice v6.1.1 and latest connectivity firmware on an nrf52832 (s132) which is connected via usb-uart.
We were previously using...
Hello!
I am flashing software over USB as I do not have a 10-pin JTAG cable yet. After I flashed a sample file on to the Thingy91s SIP it is no longer showing up in nRF...
When using LE Audio with multiple sink devices, can those sink devices also communicate between them via master Bluetooth source? For example: During streaming audio, 2 or...
My goal is 11.25 ms for connection interval with iOS. With PC and Android i can setup it.
Following Apple guideline, I added HID service to my custom device(it works, i...
Hello everyone,
I'm a junior engineer in a company, and I'm assigned to that project which we will use a different microprocessor with BLE in it, and it needs different...
I am currently working on a project with a nRF9160 and in the very early stages of evaluation.
I have a few, hope not too many questions that I hope can be answered here...
I have been struggling to get the DFU in our own application to work. When starting a DFU from the desktop nRF Connect 3.4.1 it reports an error:
According to the log...
Hi,
We are using nrf52840 development board and segger embedded studio. I am using thread concept here to run another function in parallel to my main function. i want to...
Device: nRF52840, nRF5 SDK16.0, Softdevice: S340 (ANT_s340_nrf52840_6.1.1)
Hello,
As next step to increase usability of our product and adding new features, we have...
I hope someone is able to answer a few question.
I read quite a lot but still some things are still confusing.
If we use e.g. the AMB2621 Module of Würth, is skipping...
Hi,
I am trying learn about IO/ events that can wake-up nRF52833 from lowest power mode.
What qualifies as event that can serve as wake-up source?
Is it possible to...
Dear sir,
Got error while uploading .zip in DfuTarg as "SD version failure". I'm using nRF52840 DK board. I have tried to create .zip by --sd -req 0xB6/0XAE/0xA9. zip get...
