I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello,
I am using nRF52840 S140 V7.0.1. I am using ble_app_multirole_lesc example. I changed roles from “Central and Peripheral” to “Observer and Broadcater”.
My understanding...
Hi
nRF52840 SWD is push pull or open drain type?
And we want add level shifter between J-Link and nRF52840, do you have recommend level shifter PN? Or what type of level...
Current latest JLink firmware won't allow PPK working with DK RTT debugging.
The cause is the JLink chip on the DUT board won't put the SH_SWO/SH_SWCLK/SH_SWDIO in hi-Z...
I am working with the chip ISP4520 which combine Nordik NRF52832 and LORA semtech. I use nORDIC sdk 14. I burn the FW to the chip using Nordic development kit connected by...
Hi,
I tried a light-switch example from SDK for mesh ver 4.1.0 on two nRF52840 DKs(first board with client and the second with server). I configured them with nRF Mesh app...
Hi,
I have an unkown problem in my nrf52 application. It happens rarely, so I have no idea where to look at the moment. The only thing I know is that the WDT works and resets...
I have browsed through the forum and i couldn't find a similar question, so here I ask :
I have an application running a modified example of the Mesh Client & Server merged...
Hello there,
I'm trying to use my NRF51822 custom board as spi slave with BLE that sending whatever received from the master. I'm using MSP430FR5994 as the master.
I...
Dear Nordic,
I'm new in Bluetooth mesh and Nordic SoC.
I want to develop network of measure devices connected to each other using Bluetooth mesh. All devices need to report...
Hi all,
I installed this app on my nrf52832 DK and it works great. I'm totally newbie with Nordic and its hardware so i can't figure out how to adjust this code so the app...
Hello,
we are upgrading our application firmware to the v1.3.0 of nrf-sdk. We have now encountered a problem in which the build process just freezes/stops without exiting...
I try to build and run a "blinky" example for nRF52840 DK and nRF5340 PDK. And in the case of nRF52840 DK everything works properly. I connected to the boards and saw UART...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi,
I have a topology which has 20 to 50 nodes and these nodes should send a data packet of approximately 20 bytes at 50 Hz to a single gateway node. Is BLE mesh suitable...
hello nordic
i have been working with nrff52832 with the SDK16.0 (also working with s132 if it matters)
it is a real head braking to deal with your never ending sdk_config...
