I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi everyone,
I use nrf52840 DK with Segger embedded studio. I have created a project where I read several sensors data and send these data to mobile through BLE UART.
...
hi,
is it possible to use a j-link programmer like this one in the photo, to program the adafruit nrf52840 board ? is the development procedures will be same as using a...
I am using s132 v5.1.0 and am in the process of implementing an error-handling architecture.
I'm noticing that much of my error handling could be avoided if there were APIs...
I'm trying to get mcuboot to run on the nRF52840 on the nRF9160 board. I have been able to configure it and get the resulting merged.hex file loaded on the processor and it...
Hello ,
I am using a Laird's BL651 module that has a nRF52810 chipset. I have modified the ble_app_uart example to take a command from Rx characteristic and send a response...
I'm working on IEEE 802.15.4 network using nrf52840 DK boards. I'm making use of the examples in 802.15.4 (secure). I wanted to know how the reception between a transmitter...
I am using SDK v15.3 and modifying the ble_app_uart_c example to setup ble_nus connection between nRF DK board and a custom peripheral. I can use nRF Connect to send and receive...
Hello,
I am using nrf52832 with nrf Mesh DK. Is there a way to unprovision the board from the hardware or command line and not from the app?
Many thanks in advance , ...
Hello , I noticed that my NRF DK advertises for a few minutes and goes back to sleep , because of Advertising Timeout set (I am using the BLE Peripheral Example) , but when...
hello,
I am using SDK v15.2.0,s140,pca100056. In my custom application I am using 3 SPI, RTC, timers, USBD, etc.
Actually during the development stage I have used DEBUG...
Hello,
I am trying to understand the working of BLE Mesh network and have the following question.
Is it possible to make phone as Proxy as well as Provisioner? BLE...
We are planning to build a product based on nRF52811 SoC, which is Bluetooth 5.1 and has AOA and AOD features. Unfortunately, Nordic's hasn't released any new supporting Library...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
I'm running an application with freertos and wdt and have the openbootloader and s140 also flashed.
- if...
Hi,
I have an application which has 2 services and 3 characteristics. I want to keep the value of characteristics when the characteristic value changed. I tried FDS and...
