I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello,
I'm working on a project where we are doing the following:
Collecting sensor data and storing it in an external SPI flash
Retrieving that sensor data from the...
Hi,
When publishing a message with access_model_publish() the p_message->p_buffer must be remain valid until all retransmissions have completed for loopback message but...
Hello
I want to modify the tx powel level to 4 dbm using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, 4); after Advertising_Init function.
I could...
Testing with the NRF52840 dongle and the Power Profiler Kit. I see a reading of ~5uA when sleeping without SAADC enabled.
I use this code to enable SAADC
My power...
Environment
- DK 0.8.2 in which SB44 is cut, and P1 and P2 are connected - firmware v1.0.0 - program : asset_tracker - SIM: iBasis
Before updating firmware, asset_tracker...
Hello. Got such a problem. I use nrf52832 Adafruit Feather board. While working with BLE examples (Softdevice and app.), debug via serial works fine. Can see all the text...
Hi,
I have a desig where the space is minimal and I have one nRF52838 and one nRF52840 microcontroller. Is it possible to place them at the same coorinates, but on oposite...
Hello everyone and Good day
I am a fresh graduate and its my first assignment at my job. I have to flash an LED at 1 Hz using NRF52810 BT 5 chip.
There are so many development...
Hi,
I am using nrf51422 interfacing with Ti's CC256MODA Bluetooth so here can you plz tell me how to do pairing with the TI's bluetooth .How to give passcode to the device...
Hi,
for my nrf52840 based project, I need to following peripherals :
2 X SPIM Master
2 TWIM Master
1X TWIS Slave
Given the resource sharing constraint, is this...
Hello guys
The nrf52832 uses 32 Mhz oscillator but I couldn't find much information about the oscillator in the chip document.
Can you give me a datesheet or something...
Hello,
when i try to flash code after loading s132 softdevice using nrfgo studio, i am getting erase failed,cortex-M4 error . but the fresh ble_peripheral alone is working...
Hi,
My goal is to send raw frames to some external device which is not nRF BLE example but commercial used device.
It is using some fixed service with fixed UUID and I...
