Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
It's needed to stop the advertisement in my project. I try to stop it directly by using interface sd_ble_gap_adv_stop(), but an error indicating NRF_ERROR_INVALID_STATE...
We are using the nrf51422 qfn 48 and nrf51822 qfn48 in a design.
I understand with the QFN48 we should use BAL-NRF01D3
devzone.nordicsemi.com/.../nrf51822-moving-from...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi Nordic,
We are working on Android and iOS apps. Currently using S3 with Android 4.3 and Note to communicate with nRF51822. Baud rate of 19200bps for our serial communication...
Hello,
Is it possible to increase the accuracy of the advertise interval? Im attaching an oscilloscope screenshot showing the S110 device advertising with a 20ms interval...
Hey All,
I am working on a board that is based on the nrf51422. The system goes to sleep and gets woken by an interrupt. One of the programmers claims to have managed sleep...
We use nRF51822 with S110 as a peripheral connected to iPhone master and looking for RSSI.
RSSI with correct value is received by the peripheral application every about 1...
Are there any sample applications that use a joystick press as an interrupt instead of a button press? The dev board I'm using uses the nRF6350 display and I was wondering...
Hi
I used the example from nrf51822_v4.4.1.31827\Board\nrf6310\spi_master_example for my PCA10001 board, as I know the pins configured in this example are for nrf6310 board...
Does anyone know how to implement a wrist watch LCD display? I mean a bare LCD Display, without a pre-build driver (I2C). Can I do it directly or I need another IC to drive...
Does anyone have any solid numbers on the maximum throughput achievable on
the nRF51822 USB dongle that comes with the nRF51822 Eval Kit?
Application - OTA protocol Gazell...
Dear Support Team,
currently I'm working on a custom board which contains the NRF51822_QFAB_A0.
I installed the softdevice (not the most recent version, but a version...
Hi,
I have bought nRF Beacon Kit, and I have downloaded "nRF Beacon Android 4.3.zip", but I can't find nRF Beacon Service source code.
Where is it? Please tell me.
...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
