Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hello,
We are designing a product based on the RAK4630 module that integrates nRF52840 SoC.
Since we are creating a low power consumption and battery operated product...
I am trying to set up the AT library to directly talk to the modem through a uart on the nrf9160DK. But when I enter the commands to test "AT+CFUN?" I just get it echoed back...
I'm working with a Fanstel BT40 module which includes an nRF5340 and nRF21540 FEM. As a starting point I'm using the scan_adv example, which is working out-of-the-box but...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
Hi, Iam trying to run c++ code on nrf52840. I got working C code, so i try only change .c to .cpp. I got some errors but most of them are solvable by putting libraries(.h...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
I have successfully managed to incorporate the hard-float build of the library for the nrf52840 into my bare-metal application ( custom hardware with an nrf52840) and have...
LED5 is blinking very fast. no appearance on computer at all. nrfjprog --recover not reconvering, Tried another PC, another cable and no response at all.
I am trying to read the WHO AM I register of an ICM20948 over SPI with nRF52832, but I am getting incorrect values.
I have tried different SPI modes, but none of them work...
Using Zephyr (cf2149caf2) / nrfSDKConnect on a nrf5340DK board.
I need to know how to get a direct stack trace (with file/line numbers if possible for a debug build).
...
Hello Nordic.
I used nrf52832 and nrf52840 by nrf sdk.
But I need to develop nrf5340 now, and I understand I have to use ncs to develop firmware for nrf5340.
I have...
Dear Nordic Community,
I am trying to implement a porting of micro-ROS framework on the nRF52840 chip. As stated in their tutorial , the framework is compatible with the...
