Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
I heard that nrf52832 rev3 has been released. Our product is using nrf52832 rev2, nrf SDK 15.3. If we change the chip to rev3, can we use the firmware without modification...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
As we can see that there is...
Hi,
I am trying out the smp server example with mcuboot and encounter this error when building for the nrf52840 dongle.
I read that it has something to do with the usb...
1. Erratum #7 counsels to add a DSB if reading sequentially from UICR and program flash, as below. But what constitues sequential? If my program reads from UICR on a thread...
I have a BLE application I'm writing using SDK17.0.2, and want to use FDS for some persistent storage. The first thing I want to do is to allow the user to update the name...
Hi,
I am using nCS v1.8.0 for application development on nRF Connect extension of vscode.
But I am unable to configure any unit testing framework to test my applications...
Hi, I am developing a logger for which I am using a memory. I was doing all this using SPI in nRF52832 DK which works perfectly fine. But the problem arises when I am trying...
I have a module using a Nordic chip labelled "N51822QFAAH01621UT". I know it's the NRF51822-QFAA, but I am not sure which model exactly?
Looking on DigiKey these are the...
This is more of a question than a problem:
I have been studying the ble_app_uart_c code and noticed that although data is transmitted to the handler one byte at a time,...
Hello.
We are looking for a viable solution on how to transfer a firmware over the BLE OTA from Particle Tracker (Gateway), or any other mcu to nRF52840 devkit (Client)...
Dear, I am new to Nordic. I trying to understand the various Defines for nRF5340DK kit using Devicetree.dts file. In that, I had look on SW0 defines.
1. The gpio0 reg is...
Hi, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v5.0.0_src) and some other sensors which drivers are written by using nRF5_SDK_17.0.2. my device is battery operated...
In nRF_SDK_for _Tread_and_Zigbee, we used to set autocommissioning as false in the "thread_configuration_t" configuration and then start joined so that my thread node used...
