Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hello,
I was using the send example which is located in C:\v1.5.1\zephyr\samples\drivers\lora and trying to send a message to an Arduino LoRa gateway.
However, I found...
Hello everyone,
I am stuck at a problem that I cannot resolve myself but I see that other people in the forum don't experience such a behaviour of their nrf52832s.
I want...
Hello,
I've been using SES for ARM (Nordic Edition) V4.16 (64-bit). I am working with nRF9160 sample code. While attempting to explore the code, when I right click on...
The program flow of the slave is to sample the analog signal source through the saadc and then send it to the host through the nus. When debugging on nrf52dk, configure the...
Hi,
In my main function, I just call a acceleration_read function to get data from the accelerometer sensor and call a NRF_LOG_INFO function.
But there're something wrong...
Hi,
I try sdk 17.02 nRF52840 usb audio demo,I want to achieve 48KHz stereo music play by a I2S DAC.
I finished adding DAC for I2S to play the sound data of USB Audio...
I am declaring the variable in one of the hardware drivers files that are provided by the nordic semiconductor. The variable is not static. The variable inside the function...
Are there any other QFN package baluns that we can use for NRF51822?
One suggested from STM is BGA, and I wanted to see if there are any recommended QFN baluns that we can...
Hi Nordic,
I have an NRF52805 board [ from Raytech] and I am implementing all my application using SDK v15.1.0.
As of now, I have implemented my application using the...
Hi,
We need to know rated output and gain of pcb antenna on nRF52 DK for a technical standards conformity certification.
Can you give us them and their evidence?
Thank...
I want to connect an LTE antenna to J1. However, the antenna has a normal male ufl connector - it appears not to fit.
Is an adaptor needed for this?
Thx for any suggestion...
Hi ,
my environment details:
nrf connect sdk
nrf5340 dk
segger embedded studio
I have seen I2C example code in below path
\v1.5.0\zephyr\samples\drivers\i2c_fujitsu_fram...
app_timer2.c from SDK v17.0.2 has a possible race condition in app_timer_start()
This calls the get_now() function which compares a "now" variable to a "m_stamp64" variable...
Hi,
I am developing based on the mesh dimming example.
I want to use a timer for some status LEDs and some other things. I am trying to do it using timer 0, but the callback...
Excuse me:
The default stack stze setting of SDK is 8K,If the stack overflows when the customer reads data from flash， Does stack overflow modify other...
