Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi all. I am trying to work out if the following is possible;
At the moment I have setup a freq counter (analog signal) on the nRF52832. It uses the comp to detect up crossing...
Hello everyone, I'm using the nrf9160-DK and I'm trying to read data from an external sensor over UART and I'm a bit lost. I would appreciate if someone could point me in...
I'm in the process off trying to learn the world of BLE. Currently, I'm using nRF Connect for Desktop (w/USB dongle) as the learning platform. Using 'Server Setup' I configure...
We use the chip product of nRF52810 to do a wireless module design. While in sleep mode, we found some spikes, which are 0.6mV in amplitude and 180ms in period. It is not...
Hi,
we use CC310 (in nRF52840) in a project (working directly with the CRYS API from SDK 15.2.0). When doing a test of ECDSA with secp256r1, following the one given within...
Hello,
I am trying to change the tx power for my nRF52-DK which is having nRF52832 chip. I trying the following code to change the tx power to -40 dB.
int8_t tx_power_level...
Is there any example about the dongle nrf52840 act as a central? Is that possible? In that case for a ble connection between dongle and board a service does to be create on...
Hello,
I need to long WRITE AND long READ from a central/client (android) to a peripheral server (nrf52). when I says long it means longer than the MTU.
LONG READ
I...
At the top of the Nordic home page, there's a link for "Bluetooth Software":
Following that takes us to https://www.nordicsemi.com/Software-and-Tools/Software/Bluetooth...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
Hi,
I am facing problem while developing code for the application.
I am working on the "ble_app_uart" example code to develop my one of the application, But after making...
