Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I am struggling with the correct value to use for DFU_APP_DATA_RESERVED in the bootloader. My application uses the Device Manager and has one block allocated for to pstorage...
My app is generating hardfualts. Based on this post I looked at memory location SP + 0x14, which points to the address that generated the fault.
Memory at SP+0x14: 8F 31...
Hello Everyone,
I am doing the rough calculation of the power consumption of NRF51 where in the radio part of the datasheet it is indicating 10.5mA whether it is denoted...
Hello ,
I'm using a couple of nRF52 dev.board (one is Nordic preview dev.kit , the other one is a Rigado BMD-300) , with S212 ant+ softdevice . I'm able to deep-slepp the...
I use the board to act as relay.First ,i scan and connect to one peripheral.Then ,i want to disconnect the peirpheral once the another central connect to my board.i call sd_ble_gap_disconnect...
Hi ,
Would you help me to find right material(App note, source code/project) to implement below case:
My nRF51822 connected on beaglebone black(BBB) over UART this will...
Hi,
I want to implement a DC/DC converter setup schematic for my projet and I don't know how to make the difference between the AVDD and VCC_nRF supply tags given in the...
Hi, all!
I have a Quesion about Maximum Voltage & Current of internal DC/DC conv. & LDO of nRF52832.
I'll design circuit using olny internal DC/DC conv. & LDO of nRF52832...
Hi.
Is there a (lazy) (dummy) comfortable way to make an nRF518 chip (in my case, nRF51822) communicate with the built-in bluetooth adapter of a laptop with windows 7 or...
Hi,
I am trying to connect a GPS through UART to nRF52 and get the reading and write it to the serial USB of my PC. I am using app_uart_init() and app_uart_close(). My idea...
Hi, I would like to handle in the twi_event_handler the case when the p_event->type == NRF_DRV_TWI_EVT_EVT_DATA_NACK differently and not treat it as an internal error.
...
I'm trying to use separate antplus network key, but I still can receive messages from devices that are configured with another key. Device A was using network key 0,0,0,0...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...