before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I've got a project that works perfectly on the PCA10028 DK. But the behavior is quite different when downloaded to my nRF51822 production target. My target is connected to...
Hi
I use nRF51822 of Gazell mode and RXF2401C(PA)
PA's TXEN has been pulled, what RXEX in there enbale and disable it?
(Host and Device must be)
Thank you!
Hi everyone,
My question is how much current it´s capable to sink an I/O pin configured as output ´0´ ?
In my case I have to discharge a capacitor throught an output...
I am using sd_power_system_off() to enter System Off. It is my understanding that all peripherals are off in System Off, but that GPIO configuration is retained. I have a...
I have the following code
// Initialize timer module, making it use the scheduler
APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
In the ANT Message Protocol doc, section 7.1.1.1, and in example code, the Device Number is treated as a uint16_t and shown as a two byte field in the flagged extended data...
Hi,
Will something interesting happen when the text segment on a nRF51 DK exceeds 64k? I am using Eclipse/gcc for developing, based on the tutorial provided by Nordic....
Hi,
I am developing a program on a Nordic nRF51 DK, using Eclipse/gcc, and am using J-Link RTT for a debug command line interface. This has worked very well for some time...
Hello,
I've been looking a bit into the nRF52 product specification and I was just wondering how powerful EasyDMA is under extreme conditions.
Let's assume the following...
I am currently working on a device using a nRF905. We want to use the device in Region 2 (USA).
This means that we need to use frequency hopping between 902 and 928 Mhz....
Hi,
I'm implementing a simple bootloader which will not use BLE.
Application will transfer the data from mobile devices using BLE and this data will be stored to...
I'm looking for a smart solution to connect my application to different ANT+ sensors and transmit a logfile to a mobilephone via BT (and receive notifications from mobile...
Hi~ Sir:
I test S120 connect with S110 have problem ,test methods are as follows
S120 connect with S110 ,function ok.
S110 Power Off and On, the interval time about...
Hello everybody,
I've been digging through the forum and the documentation for hours now. But to be honest I don't understand the whole timer thing.
I need a simple...
