before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
I have a modified asset_tracker_v2 running with SDK 2.5.0. It is connecting to AWS and sending data perfectly. It has been running for several years without a problem. I am...
Hello,
I’m running the AWS IoT sample on nRF9160DK v1.1.3 using nrf-sdk and toolchain v2.9.0, modem v1.3.7.
Everything works fine when following the instructions with...
Hello community, I am currently looking for a solution outside the 2.4 GHz band and I came across NR+. Does it suit my needs for M2M (Machine to Machine) communication? If...
Dear Nordic experts,
My question is simple, how to get the 6 octets default MAC address by app SW in nRF52840. The question was already raised by someone some years ago...
I have an issue when trying to install nRF Connect SDK on my work computer. I have installed VScode, the toolchain and the nRF Connect extension. The next step would be to...
I have been trying without success to install either the v2.7.0 or v2.8.0 SDK onto my Windows 10 System. Every time/method I've used results in an error equivalent to
...
Hi,
SDK17, Softdevice S112, NRF52805 custom board.
I have baremetal bsp implemented but I am new to Softdevice and struggling a bit with an interface concept beween two...
Hey,
I'm using the nRF5340 and want to run the PTS test with the following configuration: The CAP initiator establishes two audio streams within a single connection to the...
Hello,
We are currently experiencing some unusual behaviour on our feather board (circuit dojo, nRF9160 chip) which we are seeking advice on.
Whats happening:
Device...
Hello,
I'm using NRFX PWM directly because I need something more custom than zephyr's PWM driver provides. I'm trying to understand what .pin_polarity field in the config...
