Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hello,
I am trying to sample and reconstruct an audio signal using the SAADC and I2S respectively. I have a double buffer setup for the SAADC, where we process the data...
Hi,
I've noticed several times now when the NRF9160 comes out of a PSM sleep cycle that when a call to an underlying socket connect(), or nrf_getaddrinfo() call (whether...
HI,
I am developing an application with 7 transmitters and 1 receivers. Transmitter are nrf52832 with MPU9250 IMU (Holyiot YJ-18008) . I am hopping to each transmitter...
I successfully compiled and loaded the UART/Serial Port Emulation over BLE example on an AdaFruit Feather board.
I can connect to the Nordic UART Service, then send data...
I have built my application on ble_app_uart in keil in SDK 14, so I just did the same and copy-pasted my code into the latest ble_app_uart example built with ses in SDK 16...
So far i've failed to find a single source that contains comprehensive information on where errata items have been addressed. I do have multiple unrelated sources for information...
Hello, I want to try the secure bootloader + softdevice 7.0.1 + ble app buttonless dfu example from SDK16 I want to test all that in our custom board NRF52832-QFAB (256k flash...
Hello, I modified the ble_app_blinky example to work on our board (removed leds and buttons) and modified the board pca10040.h the new application worked on the devkit but...
Hello, I am completely new to embedded software development (so far I have been using development boards such as Teensy, Feather and Arduino) and I recently acquired the BLYST...
Hi
I'm currently look into the noise floor of the SAADC samples on a custom PCB with a nRF52
I'm running the ADC at maximum sensitivity (4x gain, Vref=0.6V) differential...
Hello
I have a power constraint device. Limit is not the total charge of a battery or so. Limit is the peak current.
Available (peak) current is around 4mA (@1.8V), current...
Hi,all. i face a problem that i used lightblue on iphone6(ios8.3 12F70) to connect my device(nRF51822),after sometime,disconnected automatic.
lightblue says:The connection...
Hello Community,
does an opened timeslot session affect my power consumption?
I need a cyclic timeslot for my application and I'm wondering wether it generates an incrased...
Dear team:
I have a question with nRF52832 XATL 32.768K. When I used 13 GPIO to be a interruption，the internal clock delay was more slow than before。what was wrong with...
