Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Dear Nordic:
Hi,i install nRF Studio <nrfgostudio_win-64_1.21.2_installer.msi>, and i want to erase NRF52840 flash,but when i click on "nRF5x_Programming",i cannot get...
Hi guys! I feel really excited about working with Nordic Semiconductors, but I have a problem with PWM driver.
Do you know how to support 13 independent devices that will...
Hello,
I was looking into the nRF5280 and was going to purchase it. But I had some questions that were not cleared up in the data sheets. It seems that a battery or a power...
Hello Everyone,
I have been using nrf52840 DK for several weeks. However I find it very difficult to understand the source code. I have experience only using arduino programming...
I've been attempting to use PSM but got an error.
I've already checked the post below. I download the project file and fixed a bit.
https://devzone.nordicsemi.com/nordic...
Hello .
I am looking for a way to pass the calendar time from the PC by the emulator to the MCU on first run.
I am using Segger Embedded studio 4.12
Is there a function...
I get the following error when launching the app, and the "Start scan" button either doesn't do anything or can't be clicked.
Error while probing devices: Error occured...
Hi
I am measuring the current consumption (with an amperemeter) of the nRF52 on the PCA10056 Devboard. The nRF52840 is supplied directly by connecting the external power...
Hi,
I have a problem when I do a write request on a 20 bytes characteristic from a custom service.
The funtion sd_ble_gattc_write return error 0x7 but I can't find what...
I want to stream a mono audio signal with high bandwidth (20kHz) from a remote device to a base device.
Need to A2D signal on remote and D2A the signal on the base. Low...
Hi,
The SEGGER have released a JLink software version that support to use JLink on ARM Linux platform。
I try it on raspberry pi, and it work well. But when i use pynrfjprog...
Hello.
I have a project that use the NRF_LOG_INFO for printing messages, and it is work O.K.
Now I add a part that need also to get parameters from the terminal.
I can...
Hi
Please advise when I can find firmware for nRF52840-DK which can send advertising packets or any data packets at data rate 125Kbps and +8dBm output power
I have two...
