Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
is it possible that there is a mistake in the infocenter documentation of SDK v.15?
In the bootloader description under MemoryLayout:
Usage
Memory range...
I have recently downloaded nRF5_SDK_15.0.0_a53641a and tried to compile and run the ble_app_hrs on the nRF52 Dev Kit. I am using IAR-EWARM v8.30.1. The Soft Device is s132_nrf52_2...
RE: nrf52840QIAA - Can you recommend circuitry necessary to switch source between the usb and LiP battery? Can you recommend inexpensive/small footprint boost circuitry to...
Hello,
I control buzzer using below API.
I want to know the maximum value of period_in_us .
Thanks.
******************************************************...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project: C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\cli\pca10056\blank\ses
I...
Hi,
I use STM32F103 as a receiver.
I read FIFO STATUS and STATUS register then execute FLUSH_RX command through SPI.
I continuously read FIFO_STATUS and STATUS registers...
Hi,
I asked previously about power efficiency for the NRF52840 SDK version V15 ( https://devzone.nordicsemi.com/f/nordic-q-a/36083/maximal-power-efficiency-in-main-loop...
I have an idea to open the source code of my personal project, since some source code of SDK are used and modified, is it OK to include the modified SDK source code in the...
I am using nrf52 developmemt kit. I am using mpu9250. the odr of mpu is 100 Hz. i am able to send data over ble using example code nrf5-ble-mpu-data-ready-interrupts . Now...
I' m using the nRF51 Dongle (PCA10031) for the evaluation of the OTA DFU bootloaders of SDK15.0.0 with the NRF52840 PDK. Using the PC tool nRFConnect V2.3.2 with the App Bluetooth...
I'm developing a product with the nRF52840 using nRF_SDK 15.0.0 and s140 v6.1.0. Since my device is not power constrained, I want to maximize the range, so I use Coded PHY...
It is stated that the advantage of a Softdevice is that because it is a precompiled binary file it can be used without requiring any particular compiler or linker features...
