My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hi there,
In the process of moving from SDK 10 to SDK 11, I've also been migrating an accelerometer driver over from using straight nrf_drv_twi code to the higher level...
Hello,
Is it possible to use easyDMA to transfer from GPIO to memory without involving the CPU? We need to read from a parallel bus for a short duration, without losing...
When setting up a 1Mhz square wave using NRF_PWM on the NRF52 or GPIOTE on the NRF51 while BLE is advertising, the PWM stops when the radio is active. The problem doesn't...
Hi,
I'm developing a BLE application for the nRF52 and I wish to use directed advertising and the whitelist.
I initialise the Bluetooth advertising using the following...
I have been using softdevice S130 version 2.0.0-7.alpha with SDK 11 in Keil using the pack installer. How do I change my project to work with the updated version that doesn...
Hi,
I believe there's a minor bug in low_power_pwm.c regarding pwm_state.
The routine low_power_pwm_start sets the pwm_state to NRF_DRV_STATE_POWERED_ON ; but it then...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I am troubling shooting some issues between my device and iPhone using nRF Sniffer.
One of the errors the sniffer captures is this:
Master to Slave: Rcvd Read By Type...
I will be using the nRF52 adc from -20C to 85C and am trying to determine if I need to calibrate and if so how much temperature difference I can have before it is time to...
Hi, I'm working on the nRF52 with S132 v2.0.0.
I am using a self-implemented "connection manager" that tries to establish bluetooth connections to pre-configured auxiliary...
Hi,
I am using 2 x AA batteries which gives 3V. Planning to enable all the internal LDOs (1.2V, 1.8V and Radio LDO).
VDD and AVDD are shorted on Board.
Will the device...
Is there a porting guide to this?
Custom hardware
Central device
SDK V11
I'm getting a reset in client_handling.c::ble_stack_init();
Right after I set the clock as...
Even I am writing BLE applications, but I don't totally understand these items:
In Characteristic Properties of GATT Characteristic metadata
We have read, write, notify...
I am trying to trigger some functions based on some pre-determined timings. I tried to do that using nrf_delay_us and also using timer0 interrupts, but both are giving me...
Hi,
I'm using nRF Master Control Panel to test a Phone Alert Profile (PASP) I've implemented. For this, in the app I configured a GATT server that exposes the Phone Alert...
