This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
I See in the discussion that I can see I/Q for AoA.
I see this examples "direction_finding_connectionless_rx" on zephyr I Think that I can start debug using the data from...
I want to transfer a few bytes of data between two NRF52 modules.
I have checked out the BLE Blinky and NUS example and understand the gatt client and server ideas.
My...
Hello.
I am using SDK version 17.0.2.
The example code uses nrfx_spim . Target board nrf52832
The nrfx_spim project confirmed that 10040 did not exist, only 10056...
hello,
in the case
Case ID: 227777
https://devzone.nordicsemi.com/f/nordic-q-a/46439/turning-services-like-hid-on-off-without-disconnect/309149#309149
In the...
I've got a Thingy:91 plugged into my computer and can see its USB terminals (/dev/tty.usbmodem143101 and /dev/tty.usbmodem143104). I can also see the "ZEPHYR USB" volume and...
Good morning,
I am working on nRF52840 DK, using nRF5 SDK.
I am trying to communicate using SPI.
However, I found out that the function nrf_drv_spi_transfer took 10µs...
I am developing a solution with the nrf9160 that should use LTE and GPS at the same time. But unfortunately I am having some problems. Perhaps somebody from Nordic or the...
Hi everyone,
I am working on a project using nRF905 as an emitter and another Receiver(different than nRF905), the receiver is programmed in a way to perform some actions...
Hello Nordic Team,
I am having issues with the peripheral_uart firmware for the nRF52833.
1.I can use UART_init() or nrf_drv_uart_uninit() in nRF52-SDK to enable or...
hi all, 1. may i know how to get started of designing an AOA, mainly on how to send a CTE packet from TX to RX is there any code base or command that i can use? 2. i had noticed...
I am trying to establish a tunnel from ZigBee client to ZigBee server on nRF52840 using "nRF5 SDK for Thread and Zigbee v4.1.0".
Starting with the examples "examples\zigbee...
Hi everyone!
Challenge :
I'm trying to stream data from 9 nrf52832 (12 bytes each) to a computer, hopefully at 25 Hz at least (it seems more than realistic!).
Dream...
Hi !
I want to send simple HCI commands, such as reset, to the nRF5340 via UART. Therefore, I'm using the sample "hci_uart" available with nRF Connect SDK v1.5.0. I am sniffing...
It would be great to get some reassurance on this design. Is it ok for production i.e. is robust and within limits?
I am successfully driving an smd rgb led by sinking 2ma...
I am using the https fota, aws sample OK.
testd the aws certificate via Linux PC this way:
openssl s_client -connect kamacodeetrog.s3.us-east-2.amazonaws.com:443
now...
