Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Dear nordic,
I want to make a PWM with frequency 1 HZ - 100 HZ and pulse width of 100 us. i see several demo in PWM .
can you help me how to make this ?
what parameters...
Hello, after following this tutorial https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial I have set a custom service...
I'm using the SAADC peripheral by controlling its registers directly (no SDK or MDK HAL). I have an application that alternates between two configurations:
* One sample...
Above is my code. I am using Keil uVision5 IDE on Windows 10. I am flashing s132 and then application hex to device using nRFGo.
My goal is to take a square wave as input...
hi,
I am using nrf52832 board,sdk 15.0,soft device s132. i can upload both soft device and bootloader, after that how can i upload my application file .i want use both uart...
Hi all,
I am working on sending messages from nrf mesh app (proxy client) to proxy server ( nrf 52832 DK : running light switch example from nrf5 sdk for mesh v. 3.1.0)...
I am trying to program an external board nRF52810 using debug out on PCA10040. I was successfully able to program an external PCB board with nRF52832 using PCA10040,
but...
Hi folks, I'm receiving a special timestamp over bluetooth, and I want to write it to an external memory. I want the time at which it was written to the memory to be as precise...
I use Nodic sniffer nRF_Sniffer_200_beta3 to capture BLE Mesh packets, but found one strange scenario:
1 if set channel filter 37, 38, 39, can capture 3 packets in channel...
Hi,
going on with the migration from SDK 14.2 to SDK 15.3 it keeps on making trouble. Now the spi_mngr is not working anymore. After changing all calls to perform with extra...
We are using the SPIM driver to support a propriety 1-wire protocol used by a TI LED driver (TLC59731). To do this, we're using the MOSI pin exclusively and, for it to work...
I have been trying to get 125Kbit and 500Kbit coded phy wokring by directly using NRF_RADIO API (no softdevice in use). I have followd for example these instructions, but...
Dear all developers,
I'm currently studying about nRF52832 SoC and prepare to develop low current BLE device.
Before starting, I want to know about idle current consumption...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
