Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi all,
I have been stuck trying to debug the example project for a couple of days now and could not find the answer through searching. Here are my problems.
Background...
Hi All
I have a bunch of nrf51x22 (4,8) and I'd like them to read their own firmware data and send this to others that are in DFU mode using the over the air (OTA) method...
Dear Nordic Developer Zone,
I'm using nrf51822 EK testing the GPIO sense function. The code I'm using is based on what a nordic employee has posted elsewhere in this dev...
hello,
i was trying to compile the softdevice s130 example code given with softdevice download from nordic.
I am using the ARM-MDK lite 4.74 version. It is showing error...
My design goal is to conserve as much battery power as possible on a device that typically gathers data 30 to 40 minutes per day. To that end, our thought was to make the...
hi~
6.2.1
Updated Setup_JLinkARM_V490e to Setup_JLink_V492
Updated nrfjprog to version 5.2.0 (see own release notes for changes)
where is release note ??
i can...
Dear all:
I want to constantly transmit messages from a nRF51422 to an other nRF51422 with specific ID by ANT protocol. Then, I want to receive the messages from one to...
Hi,
I want to build a Tx that can reconfigure a channel(like change the device's number) after finding out a long time failed to send message.I use the way below:
sd_ant_channel_close...
hiii...
i hv made a custom profile with concurrent broadcast feature tested in master control panel and some other phone app... working properly.. but wen i tried in iphone...
Hi,
I try to open ANT+ channel and make sure the status is searching or tracking,
but if I use pstorage to update flash in the same time,
It will response timeout...
We are developing a keyboard for smart phone or plant and what to make different surpport for different device.
So can I make difference from ios device and Android device...
Please indicate me if there is a data port on nRF8002 after you burn out OTP, Can I use this I'c for data transmission. Please indicate communication port for this chip. Also...
Hi,
I'm testing ble_app_proximity example (...\Nordic\nrf51822\Board\nrf6310\s110\ble_app_proximity). I'm using Master Control Panel Android app version 2.0.3 and Nexus...
I'm using S110.
I have a characteristic that is writable from phone client. However, the characteristic has lower and upper limits (an acceptable range) for the application...
Hi experts,
I'm trying to bond device between my android phone and the Nordidc51822(S110 v7.0). but I found that it's very difficult to achieve this function. Is there...
