Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I'm using the UART to talk to a GSM modem. It has hardware flow control and supports a baud rate of 115200. I'm using app_uart_fifo.c, not app_uart.c. I'm using the SoftDevice...
Hi,
Does Nordic Semiconductor provide any resources (codes, macros, documents) for work with IAR or Keil's simulator to fully simulate nRF51822's peripherals?
Thanks...
Hi,
I do:
err_code = ble_bondmngr_bonded_centrals_delete();
APP_ERROR_CHECK(err_code);
till now all is ok.
But when I do:
err_code = ble_bondmngr_whitelist_get...
Hi,
I need to delete all centrals using ble_bondmngr_bonded_centrals_delete ble_bondmngr.c function. It is working but it is not cleaning the whitelist.
So, when I do...
In the example of hid_mouse, ble device will bond master when disconnect event happen.
I try to add this two codes to Implement my idea.
err_code = ble_bondmngr_bonded_masters_store...
I write this code to set my ble device power down,but it causes reboot without any error report.
GPIO_WAKEUP_BUTTON_CONFIG(LEFT_BUTTON_PIN_NO);
GPIO_WAKEUP_BUTTON_CONFIG...
I try to use 51822 to run ANCS sample(ble_app_ancs). It work well and I can get notification source and notification attributes. But I don't see any source code for get App...
Hi
I've a reproducable behavior i'm not able to explain. I'm using the softdevice S110 6.0 on a nRF51822.
The firmware implements some BLE profiles and uses TWI Master...
Is there a way to map external memory (SPI connected) to force the app to start execution from there ?
If not feasable , there is a way to transfer the execution from internal...
I have a 51422 board design and I just got Ant-FS working with our firmware so I can now download data from an external SPI flash to a desktop application.
I want to be...
Hello:
I am using NRF51822 to design somethings. And I want to use interrupt send method instead of polling send method.
NRF51822's UART0 provides TXDRDY interrupt. After...
Hi,
I have tested the nRF Toolbox proximity application using nrf51822 evaluation kit and with nexus4 smartphone it is working fine. Now my question is, is it possible to...
Hi
I am trying to overcome the problem that I have confronted, I have no buttons to delete bonds. So instead of deleteing this is what I did.
I modified the bondmanager...
I am developing hid_mouse . When I connect Android once and ubond hid_mouse I must set bluetooth off and on again to connect ble device otherwise it will connect again to...
