Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I've installed Zephyr RTOS and built blinky example for NRF5340-DK board. Then, when I tried to flash output hex file into NRF5340, nrfjprog (using "west flash" command) gave...
I'm trying to debug firmware on our production device, but after programming the device a couple of times, I am unable to program.
Inside of Segger I see this log:
j...
Hi everyone,
In my company we are working with the last SDK release, and we build projects with make and gcc toolchain.
I have a quite wide request : since I'm using makefiles...
Hi all,
I have a custom nRF52840 board that transmits 32-byte packets to mobile device and I want to achieve maximum transfer speed.
The code is based on the ble_app_uart...
Dear all
The issue is:
heartRate and battery levels set by "bt_gatt_notify" in peripheral hr sample on nRFConnect v1.5.0 are not shown in iphone app of "nRF toolbox" ...
Hi All,
I am using the nRF52840, with SDK140 v15.0. I have configured the nRF52840 to be a SPI slave to a NXP processor. When I connect the logic analyzer I see signals...
Hello,
I am trying to build on the nrf5340_cpuappns sample, however this snippet seems to always warn unable to allocated UART send data buffer. Is there any reason k_malloc...
Hi Everyone!
nrf_serial.c and nrf_serial.h are gone in SDK 17.0.2. There are present in 16.0.0. I do not see any mention of this in the release notes.
Was this module...
i am using example code ble_uart for controlling gpio(led & buzzer) by editing bluetooth data handler. I am driving a buzzer using pwm.
led working fine i.e turned on/off...
In nRF Connect SDK I see drivers for BH1749 sensor from Thingy 91, but not for BH1745 from Thingy 52.
Is it possible that the BH1745 sensor will be supported soon? Looks...
I tryed to use the pynrfprog with a Segger-ARM-Flasher to update modem DFU.
I changed the python skript to follow - because there are 2 Segger-ARM-Flasher installed in...
Hi,
When I connect my device to an external power supply, it restarts randomly. It sometimes happens once every minute, sometimes once every 10 minutes. I couldn't find...
Hello,
I am transmitting 1 byte BLE data across a central and peripheral and the central does other things like control PWM, sample SAADC (scan mode), GPIO pins interrupts...
Hello,
When I am loading my project into SES I get the following warning message.
CMake Warning at C:/Zypher/v1.5.0-rc1/zephyr/CMakeLists.txt:1354 (message):
WARNING...
