Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hi
Thank you for the IOS App "nRF Loader" which was released last week. It works well and offers a lot of possibilities for Nordic developpers. I've one question about...
Hi,
I have just opened my nRF8001 DK. It seems like for the evaluation of the nRF8001, I also need to purchase a nRFgo Motherboard, which is sold separetely.
Where does...
Hello,
I would like to do some code tests and simulations of my application in the keil microvision, so I would like to know if you could give me an example project to...
Is it possible to initiate communicate with an ANT+ device using a nRF24L01+?
I understand that the RF Channel is 2.466 GHz (66), however I do not know what Address(es...
hi nordic guys,
i created one custom profile, which is having two characteristics
my minimum and max conn interval is - 10ms and 50 ms
1. characterisic one will send...
Hi,
i am using accelerometer sensor, which is i2c compatible.
i have nrf51822 pca10001 board.
in accelerometer datasheet it is mention as after every write there...
The documentation clearly state that if the payload length is read as > 32 byte, the RX FIFO must be flushed.
My question is, will that erase all other pending messages even...
How much current can the nrf51822 sink per pin? In the datasheet, I can see that it is at least 5mA. I also see that the chip can drive 3 pins at 5mA, but can it handle more...
Hi
SPI master is 3rd party MCU. SPI slave is nRF51822.
If MCU sends a bunch of data to nRF51822 via SPI, at the same time, BTLE host like celluar phone try to connect...
Hi,
I am using the PCA10001 v1.0 from the development kit and am having trouble measuring the same current as the one from the specification.
I am using the ble_app_proximity...
Hi,
According to nRF51 Series Reference Manual v1.1 , section 10.1.3 there are 3 ways to leave debug interface mode after programming the chip. Assuming that my device...
Hi
i created one timer0 interrupt in ble_app_hrs.
void timer0_init()
{
NRF_TIMER0->TASKS_STOP=0;
NRF_TIMER0->PRESCALER=4;
NRF_TIMER0->BITMODE=3;
NRF_TIMER0->MODE...
I am new to ARM and nRF51822. I am using a development kit with the PCA10000 dongle and the PCA10005 daughter card. I wrote a simple C program (attached) to blink the LEDs...
Well, I'm a little in doubt on whether this is the right place to file a bug in the reference manual. Anyhow, I think it's easier and maybe it will prevent that another guy...
Hello,
I updated the "ble_app_proximity" PCA10001 example for adapting the time constants of my needs.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(3700, UNIT_1_25_MS)...
