Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I have no power on my nrf6350 display
I programed the board with the display jostick example but cant see nothing on my lcd of the nrf6350
any advice?
thanks
...
Hi:
I'm fresh in use BLE.
when i installed SDK, i could not install the lastest version v4_4_1,but can install v3_0_0.
My system is MS win XP Pro SP3.
Please tell me what...
hi,
i took the same example of BLE_LBS, as it is working properly in case of writing to the device, but when i implemented my own for writing to the server, it is not working...
Hi,
I need to send more than 500 packets(each 20 bytes) to the master for every 1 minute, through the timeout handler. But i cannot able send all the packets, btle_connection_timeout...
Hi,
i have some trouble with the method __WFI ();
I have the following code:
while(device_status == false) // Gerät ist im Schlafmodus
{
checkPowerConnector ( );
__WFI...
1.Can we use the Timer0/Timer1/Timer2 for doing something?
2.What source of IC the SD have used?
3.What source of IC we can use for our application?
4.I used the compare...
Hi - I am completely lost and I'm really hoping someone can point me in the right direction. I'm simply trying to get started with the nRF51922 development kit and nRFgo Motherboard...
I opened both the NordicSemiDemo.xcodeproj and nRFDemo.xcodeproj in Xcode 5.0.2. When I try to run them (Product->Run), I get the splash screen in the simulator, but when...
this time i have some encryption related questions to ask.
I use the "BLE_GAP_CONN_SEC_MODE_SET_XXX" to enble link encryption, doese this correct?
can i set the encryption...
Quick question regarding the boot process of the nrf51822. If a bootloader address is written to 0x10001014, will the bootloader code always be executed, regardless of whether...
Hi
I am using ble_app_hrs for my application.
in this case ble has highest priority , next gpio then timer.
if i send continuous data over ble, by using function...
Hello Nordic expert,
In nRF51822_PS_v1_3, the max bit rates for SPI master is 8Mbps(section 8.8, page43).
But in nRF51822_PS_v2.0, the max bit rates for SPI master change...
I heared a rumour that the NRF581922 will be withdrawn and an other solution will become available. We have planned the 581922 for implementation and want te release the product...
/* YOUR_JOB: Use an appearance value matching the application's use case.
err_code = sd_ble_gap_appearance_set(BLE_APPEARANCE_);
APP_ERROR_CHECK(err_code); */
Shoult...
