Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
I want to use libuarte. Target is nRF52832 and SDK17.0.0.2. Do I need to take workaround against Errata109 when using libuarte?
And, I done backport libuarte to SDK15.3...
I have been using nRF Connect SDK v1.2.0 to program my nordic thingy 91, however recently whenever i open IDE, Segger Embedded Studio gives the following error,
"Unrecoverable...
I am new to BLE and I have some question regarding Mesh and LPN which we cannot get a consistent result :
Assuming in a Mesh set up there are 2 Relay units (simply refer...
Hey,
I have an OLED trying to use, that is built in with a pcb design.
I don't know the manufacture to contact,
On my PCB datasheet says: the OLED Module QT-2028TSWIG02...
I created a TWI software module which runs well as standalone. Now I need to put together with BLE code to comunicate with Android APP. I'm stucked because when I initiate...
I am able to provision and configure 1 mesh device with the nrfMesh iOS app. I am able to successfully provision a second device, but when I configure a second device, the...
Hi,
I am trying to test and develop the DFU-OTA in nRF CONNECT SDK for nRF52832
I followed these link to develop i am using NCS v1.4.2
1. I have copied the peripheral_lbs...
Hello, teams.
Now, I'm changing the Android studio source code.
when I changed codes, it changed right away.
But when I edited some other java files such as pertage8...
Hello,
We wanted to clarify the behaviour of the ESB retransmits when noack is set to true for the packet. This is because our system is very time-sensitive for certain...
I have modified the example ble_app_uart_pca10056_s140, which is a BLE peripheral example using the Nordic Uart Service (NUS).
The key snippets are below. If send_stream_flag...
Hi all. I hope you are well! I posted this in the backstage forum but I realize that is not where it should go ;) so I repost here. I hope that is ok.
page 56 in this...
Hi all,
I am trying to write an android app and (later iOS app) that can connect with the Bluetooth dongle and send data through uart, the Bluetooth dongle has been programmed...
Hello everyone,
i would like to update the sdk of an existing project from 15.3 to the newest 17.0.2. I am developing for the NRF52840.
I am using the serial port library...
Regarding nRF52840 Dongle, how many Bluetooth devices can it receive? The dongle looks promising and since we are looking for a device that will receive data from 16 handheld...
Hi,
I am using nrf9160DK and ibasis card to test LTE-M signal. I can connect the network using LTE Link monitor as the following figure. But I can't use AT+CCLK? to get...
