Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I have used NRF52840 and SDK 13.0.0. Module SPIM.
Nrf driver does not support frequency more then 8 MHz(enum does not have constants for 16MHz and for 32MHz).
But I have...
Hi,
I tried to use fstorage to store some data in flash.
From now, I was able to read and write data before advertising starts, but when I try to write data to flash after...
Hi,
I am currently trying to perform DFU update over BLE, I am working on SDK v11.0, and Softdevice S130 v2.0.0. My traget is an nRF51822-QFACA1.
When I enter in bootloader...
Hello everybody,
I'm designing an app to track the position of the smartphone using six beacons and, in order to do that, I made some measures both indoors and outdoors...
Is there any example combining the Serial and Over the Air DFU for the SDK13?
Or the posiblity to combining the two features into a single bootloader?
What steps should...
Iprogram the bootloader.hex to 0x78000 with jlink.Then in my application program,I set the NRF_UICR->NRFFW[0] register as belew:
static void write_uicr_customer_register...
When power on,run app first at 0x1f000,then reset and run to boot loader at 0x78000,how to set UICR registers to make this come true?I try to set the NRF_UICR->NRFFW[0] in...
Hello,
I want to build a system which will use 2 nrf8001 to communicate. 1 nrf8001 will act as a client by continuously transmitting its UUID and another one will act as...
I am working on RTLS project. I want to perform DFU in beacons but not getting proper information .I went through ( devzone.nordicsemi.com/.../) but i think it i for SDK 13...
I have a hex string like this 58FF1CE5.This is corresponding to One date time 16/09/1955 .(ie in MM/dd/yyyy).How can i do this in ObjectiveC, I am getting this date in didDiscovercharacterstivc...
After some search I found that accepted values for tx power are -40, -30, -20, -16, -12, -8, -4, 0, and 4 dBm.
So my questions are
once I set the tx power using ...
I will code 1 to 2, however, was not successful
code1 :
u8 IICwriteBytes(u8 dev, u8 reg, u8 length, u8* data){
u8 count = 0;
IIC_Start();
IIC_Send_Byte(dev);...
Hello Nordic Team,
I would like to know if it is possible to do a DFU of my SDK10 based application ( s130_nrf51_1.0.0_softdevice + SDK10 Bootloader ) on an nRF51822 (32...
Hello to everyone in this community,
I am new with NordicSemi chips and I have the Development kit 52832. I opened the example folder from the SDK 13, SPI slave and i saw...
