Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi
I'm currently using power configuration example nr. 4 for my custom board with nRF52840. Can I use external DCDC for powering my other components on the board (SPI and...
In the datasheet of the nrf52840dk board, for the port P4, there are freely available pins p0.26 and p0.27. If I use those two pins in the overlay file, I am getting "Pin...
Hi there!
I'm trying to make an SH1106 screen working with my Zephyr 3.7.0 project using an nRF52DK (nrf52832-based one). My project is straightforward:
proj.conf
...
Hello,
I am attempting to use the DFU Target library to receive an update file over a custom protocol. I aim to do an MCUboot-style upgrade such that after the file upload...
Hi there,
My compiled image size in ROM is ~200kb.
I have 2 MCUboot partiitons, each 228kB.
I wanted to ask- is it possible for the application to use the second (non...
NCS v2.7.0
nRF52840 dongle
I want to program the nRF52840 dongle with external J-Link, and I can connect to nRF52840 dongle with SWD now. Using "nRF52840 Dongle nRF52840...
Hi,
I am evaluation PAWR feature and plan to use it for a product. The project is based on nrf5340.My enviroment is:
nrfconnect sdk v2.7.0
nrf5340 audio dk.
After...
Need to automate the FOTA process for devices with Zephyr build application which has mcuboot as bootloader, these devices can be programmed using nRF Device Manager and nRF...
I’m developing a product that uses the nRF9160 for LTE-M and the nRF52840 for Bluetooth. The nRF52840 is a pre-certified module, and I have experience with FCC compliance...
Is there any hardware limitations that would prevent one from using the nrf_802154 drivers on an nRF9161? If no, could you adapt the open-source sl to use the 9161 modem instead...
Setup: custom nrf9161 PCB, flashed with nrf9161 modem fw 2.0.1, using NCS 2.6.1
Targeting my custom board, I couldn't even speak to the modem lib, no IMEI etc.
So I dug...
Hello,
I have been trying to correctly setup my nRF Connect inside VS Code.
When I try to execute the command
west -V
in a nRF Connect window inside VS Code, I...
Hi i am using nRF52840 with segger embedded studio.
SDK -> nrf5-sdk 17.1.0 I want to configure rtc2 so that whenver i initialize it it should generate an interrupt after...
Hello, I am building a device which simultaneously advertises as a beacon and acts as a peripheral role device. Advertisements are sent at ~20 Hz with the connection to the...
