I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
I have an Adafruit Bluefruit Feather nRF53832 board I am considering using and need to change the default serial baudrate from 115200 to 9600.
I am told that I can use the...
Hi:
I am using a shake sensor as an analog input wake-up system. The system is not system off. The analog input signal only generates an event to wake up turn on...
I am using the UART central, integrated with peer manager and UART peripheral application from the SDK 15.3 on our custom hardware. I have 2 centrals running exactly same...
Hello everyone.
I want to familiarize with The Power Profiler Kit. I've installed proper software and been trying to connect to the device but every time I receive the same...
Hello,
I am trying to load the ble_app_hrs example from sdk15 on to my external BMD-350 module, but I cannot seem to discover the module using nRFConnect. I am not using...
SDK:
nRF5_SDK_15.2.0_9412b96
Softdevice:
132_nrf52_6.1.0_softdevice.hex
Hi Sir,
I want add NUS function to ble_app_hrs_rscs_relay sample code and I add...
Hi,
I use a central with 4 peripherals connected with BLE protocol.
On the central, I use the radio notification interrupt. I would like to know which peripheral correspond...
Hi,
I have a problem in my application, i want to add scanning feature, but
When i call sd_ble_gap_scan_start () with these parameters it returns error (0x06) (with...
I am a begineer in Nordic trying to read voltage and current readings from ADC pin. I need to read both values in parallel, with known interval. So I need to use interrupts...
I am trying to use the LTE Sensor Gateway app to send Running Speed and Cadence Service Sample Application data loaded on a nRF52832. I have managed to get this two device...
Hi,
I have a problem with timer and nrfx. I use the migration guide:
So I r emove the old configuration entries related to the nrf_drv_* drivers from my sdk_config.h...
Hello,
I am currently using nRF52832 with SDK v11.0.0 and S132 v2.0.0. I am also using the soft device as my application requires. I have been trying to put the CPU into...
Hello, When i try to use nrf9160 with the BME280 sensor over I2C i get this error
***** USAGE FAULT ***** Illegal use of the EPSR ***** Hardware exception ***** Current...
Hello,
I am using BLE+MCU MBN52832 module and i am facing one issue while programming my application.
I am uploading the hex file using nrfGo Studio and when i try...
I have a custom nRF52840 board that I am implementing the Open Bootloader (from SDK 15.3). Push Button/Power control is handled by the STM6601 device. It keeps the power ON...
