I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
I am having an issue migrating some code over from Keil to an example in SES studio.
The code in Keil is simply listening for a radio packet, when it receives it, it transmits...
Hello,
I generate a private key by using nrfutil.
I like to convert raw data format to use in the code from private key.
Additionally, I already used a nrf_crypto_ecc_key_pair_generate...
I want to drive a servo by the PWM on nrf52832. The pwm cycle is 20ms and the duty is 1.5ms. But i have a problem that the duty is not precise when the BLE is working. I need...
Hi,
I am using a Sparkfun nRF52832 Breakout board with the Arduino IDE. My objective is to control 3 SPI digital potentiometer. The problem is I don't know how to select...
nRF52840
SDK15.3
My question is regarding the low frequency clock.I am initializing the low frequency clock as follows:
When TASKS_LFCLKSTART is initiated in line...
Hi Nordic,
I have been trying to communicate with KX 124-1051 using IIC in nRF52832 . I am getting NACK from slave every time i send the device address. I checked all the...
Hy to everyone
I'm working with SDK15.3 Ble_Blinky example for my nRF52840 Dongle (pca10059).
First to know, I'm wokring with c++ and the whole Project is compiling without...
I'm using this module to develop a toy that needs a couple of sound effects. I just don't want generated tones but previously recorded audio files no longer than one second...
I wanted to try the bootloader related example. I was using the IAR to run peripheral examples.
But for bootloader example, I saw that IAR was not listed. So installed the...
I read the following QA - https://devzone.nordicsemi.com/f/nordic-q-a/41237/on-dfu-jump-address but still have doubts
1. Is it safe to set the Bootloader RAM start address...
Hi,
Hardware：nRF52840 module, Power Profile Kit. SDK：nRF5_SDK_15.2.0_9412b96.
Using Power Profile Kit to measure the low power consumption current of an nRF52840 product...
Hi,
I am currently trying to use SDK 15.3 secure serial UART bootloader (from the example in nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart) on a custom...
hi, I am working on the bootloader with s132.5.0.0 on sdk14.2.0. I am trying to using the uart to flash the chip.
I build the bootload example bootloader_secure_serial,...
I'm using three PCA10056 boards to test mesh example(Meshv3.1\light_switch).
[light_switch_client] ---> [light_switch_server1] ---> [light_switch_server2]
*Put the server2...
I am testing a mesh network, using the NRF52832 modules, SDK 15.2 and MESH_SDK 3.0, provisioning the nodes with nRF Mesh android app and using a modified firmware for the...
